Metal Recycling Entrepreneur
Just wondering if some of you experienced guys could possibly make me a list of everything I need to take off/out a car before scrapping it so I can maximize my profit..i know the basics like wiring harnesses, radiator, cat, battery, heating core and what not. I'm knew to this and just wanna get every $$$ out of each vehicle I can, thanks in advance!!!
Metal Recycling Entrepreneur
|
You listed about everything that I remove before scrapping a vehicle, other than I will also remove any desirable parts for resale, if there is a market for them. The yard that I sell to also requires the gas tank be removed, so depending how fresh it is, I usually have extra gas for lawn mowers and bonfires.
Rural scrapper
Using perfectly good gas for Bon fires ? Not in my operation, I'll run that stuff in my pickup! If I was to save anything it would be drivers side window regulator, and both inside and outside door handles if not broken already, but consider this too, I've held on to parts for 5 years before they sold before. So save enough to fill up any "spare" space you might have but more than that
Alvord iron and salvage
3rd generation scrapper and dam proud of it
Metal Recycling Entrepreneur
|
|
Like I mentioned...depending how fresh it is. If gas has been in a tank for possibly a few years, it's going on a bonfire. Where as I scrapped a car a couple months ago where the owner had just filled the tank the night before, not knowing his motor was getting ready to blow up the next morning. I pumped that baby dry for use in my truckOriginally Posted by taterjuice
Metal Recycling Entrepreneur
No other parts I should take out?
Metal Recycling Entrepreneur
You actually take more off than I do
“If I had eight hours to chop down a tree, I’d spend six sharpening my axe.”
Abraham Lincoln
http://junkcarbuyersraleighnc.com
I snag cat, tires/rims, radiator if it's copper, and battery.
|
looks on e8ay and see what parts are selling off that car then cherry pick the car, headlights, taillights, mirrors, instrument cluster, climate control panel, ecu, cylinder heads, ac system parts always sell quickly for a fair price
Rural scrapper
I sell a lot of mirrors and tail lights, after market pickup parts like grill guards, headache racks, receiver hitches, and nerf bars are also usually a quick sell if the pickup is new enough
Metal Recycling Entrepreneur
|
I have the means to sit on them for awhile and sell "as needed" parts. I keep around 100 on hand. Easy to access aluminum or die cast trim, easy access elec motors, easy access cast alum under the hood, and surprised nobody has mentioned rebuildable cores for the core buyer...automatic transmissions, 4x4 transfer cases, brake calipers, masters & boosters, PS pumps, AC pumps, distributors, carburetors, ECM's, starters, alternators, steering gears, steering racks. Probably a couple others I'm not thinking of. All of those items are worth more as cores than as scrap.
|
Some folks will take out the:
Starter
A/C Pump
Rotors
Radiator
I have found that most of these items are either: Too Time Consuming for the time vs. profit yield OR they create more mess to clean up than the hassle of the profit.. i.e. You pull a radiator and you get a nice puddle of anti-freeze mess everywhere- for about $2.50.. So I leave them.
|
|
Well you need to cut a hole in or remove the tank, so the fuel pump is always good to sell. So other items that sell well and can be quickly removed include mirrors, headlights, taillights, glove box, cup holder, radio, climate control panel. While your removing wiring you can get the ecu from the engine compartment. Also make sure to pull the ac compressor and ac bracket/tensioner, used ac lines sell very well also. The radiator is always worth pulling and scrapping, they pay about $1.30 per pound for them. If your worried about the antifreeze mess just use a water hose and do it outside.
|
|
jghilino: Where do you core your ECM or ECU's? None of the core buyers in my area seem to deal with them.. Do e-waste buyers take these?
Thanks,
Last edited by sledge; 10-01-2014 at 02:46 PM.
|
I use RAS cores >> Welcome to Rebuilders Automotive Supply
|
|
John-
Awesome.. Thanks for the link.. Maybe Indiana hasn't caught up yet with the rest of the country! Bookmarked the site you listed!
Last edited by sledge; 10-01-2014 at 02:46 PM.
|
|
i sell all the parts on ebay and craigslist, i have a couple local bodyshops and parts stores i deal with also, i sell parts to them and buy cores from them
im checking out that core buyer you posted, i have alot of parts i cant move that i would go that route on
Last edited by jghilino; 12-02-2012 at 02:15 PM.
|
|
If you open an account with them (FREE)
You can check a vehicle by VIN or make/model/yr
Some of the core payments are ridiculous >> LOW like One Dollar for some water pumps
Then some of the Jeep ECM's bring $75 to $100 on a regular basis
|
|
well it seems like i have piles of torque converters and steering racks and trannys and transfer cases thet dont sell, if they pay more than scrap and cover the shipping cost ill send to them all day long, im getting 35 cents for dirty aluminum
There are currently 1 users browsing this thread. (0 members and 1 guests)
|
Browse the Most Recent Threads
On SMF In THIS CATEGORY. 
OR 
|
Posting Permissions
Register To Reply
Bookmarks