|
It's been a few months since I posted but I'm still at it. I had a service ticket today and me and a coworker had to install a new battery backup and remove the old one. I got to keep the old one. The pic below is the one we removed and the customer has 3 more they will be replacing in the next two months that are much bigger. I'm guessing the one below is around 1200 pounds.
|
|
I wanted to share some more pics of the UPS above. The top part had a 15 inch toroidal transformer and was super heavy. The next cabinet down contained all of the big power boards and the other 6 were full of batteries. 112 pounds of batteries in each of the 6 cabinets. They're not hard to take apart, just a lot of heavy lifting. I'm going to start checking around on battery prices but most places are usually .20 a pound.
I took apart a big one similar in weight to this one. I had sooooo little to do I disassembled all the coils and windings to get the #2 cu out. I don't recommend doing that. 73, thanks for sharing, Mike
"Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}
Now go beat the copper out of something, Miked
|
|
Mike I've taken some smaller ones apart before but didn't get much copper out of them. I just weighed this one and it's 125 pounds and the center is filled with epoxy? Not sure but it would have to go in order to get to the copper. I might save it for a rainy day.Originally Posted by miked
|
That center piece will just hammer/push out....i have a pretty good system doing these
BUYING ALL COMPUTER SCRAP WORKING OR NOT
CHECK OUT MY BUYERS THREAD http://www.scrapmetalforum.com/scrap...nic-scrap.html
https://getjunk.net/Knox-County-TN-0...Recycling.html
|
|
I might have to get my BFH out!
|
|
Yea the hammer you have in the pic probably won't do the job.........I picked up a big EASTWING roofing hammer in some scrap and it weighs probably 2 to 3 times what a normal cheap hammer weighs and has a longer "shaft" to give more leverage.........It is kinda awkward working in smaller spaces but for knocking the **** out of something it does the job.........If you could get it stood upright and braced properly a sledge might do the job...........Usually I cut away some of the exopy/glue before I go to hammering
|
|
ITT 601 KSU/1A2 phone system
I installed a phone system last week in an old building that was being remolded. This old phone system was mounted on a board in a back room and the GC said I could have it.
These systems were still being installed in 84 and I got to install a few of them. You gotta love the old technology. Each phone required a 25 pair cable!
|
|
So I have an hour and a half invested in the 15 inch transformer from the UPS above. My 3 pound hammer and about 20 whacks removed the center plug.
The first layer of plastic and copper have been removed. The bolt cutters help a lot.
I'm sure there are easier ways of doing this but I'm using what I have. I'll be getting 1 or 2 more of these soon and I was curious to see how much copper is in one.
Last edited by jimicrk; 06-30-2021 at 04:09 PM.
|
|
When i did ones similar it seemed to at least double the value of item as oppossed to selling it as is
|
|
Once i get it going I unwind it until the strand of copper gets to long then I cut and repeat
|
|
Obviously it will get faster the more you do but they can be time consuming
Metal Recycling Entrepreneur
|
It's been awhile since i did one. I can't remember if i broke it like you would a ferrite.
Nowadays i think i would cut it around the middle of the outside with a 4" angle grinder. The 1/16th inch thick metal cutting wheels work so well that i use them for a lot of things when i'm scrapping.
|
|
Yes Mike it did get faster this afternoon. I was able to finish removing the second layer of plastic and copper in 30 minutes. I haven't weighed the copper yet but the metal center was 80 pounds. I'm guessing 5 pounds for the center plug and the plastic wrappings so there should be 40 pounds of #2 copper. I have no idea how much copper is going for right now. It's been a while since I had any to sell.
|
|
Congrats looks great!
|
|
39.5 pounds of #2 copper in the first pic from the big round transformer above.
Since copper is up I decided to drag my horizontal band saw out and start cutting my transformers. I can set one up in the saws vise and work on other things while it's cutting. The second pic has some #1 I stripped and another bucket with about 50 pounds of #2 from transformers.
Thornton Scrapper
|
Heads up jimi, That should be bare bright not #1. Why down grade it after all that work stripping it, just remove the buss bar copper. that should be #1 or have its own category.
By the way i watched moose scrappers copper grading video LOLOLOLOLOL. Seriously i didnt but i had to say it
I second the use of an angle grinder, its a saws all for smaller jobs. 73 and thanks for sharing. Mike
|
|
I'll check but I don't think the yards I go to have a bare bright category. I will be making some phone calls tomorrow. Thanks.
|
|
I found 15 more toroidal transformers in a milk crate. They're a little bigger than a baseball. My plans were to cut it with my bandsaw, spread it apart with a crowbar and unwind the copper.
45 minutes laterI had 1 pound 9 ounces of copper and the core was 1 pound 12 ounces of laminated steel.
I will be going today to buy a few cutting wheels for my angle grinder and do what Hills suggested.
There are currently 1 users browsing this thread. (0 members and 1 guests)
|
Browse the Most Recent Threads
On SMF In THIS CATEGORY. 
OR 
|
Posting Permissions
Register To Reply
Bookmarks