Results 1 to 8 of 8
  1. #1
    JustInTime started this thread.
    JustInTime's Avatar
    SMF Badges of Honor


    Member since
    May 2012
    Location
    SE Pennsy
    Posts
    192
    Thanks
    111
    Thanked 88 Times in 57 Posts

    What to do with this beast - Dolch PAC 65

    Trying to figure out what the heck to do with this thing....
    It's a Dolch PAC 65. Old network sniffer/troubleshooting/laptop thing circa 1999. Up until recently, it was running NT4 on it but the hard drive finally crapped out.

    It has a mechanical keyboard, one of the ones that go all klikity klikity, which I'm thinking if I sell separately I should be able to make around $100 off of(people love their mechanical keyboards). But is their any value in the rest or should it just be scapped? It has a pentium slot processor, so no ceramic. Small motherboard. Big 640x480 display... Beast weighs a good 22 lbs.

    Tempted to just sell off the keyboard and scrap the rest... Not sure yet.

    *sorry for the image sizes, was hoping the forum would resize them down a little bit*








  2. The Following User Says Thank You to JustInTime for This Post:



  3. #2
    logansryche's Avatar
    SMF Badges of Honor


    Member since
    Sep 2014
    Location
    Jamestown, TN
    Posts
    1,215
    Thanks
    1,043
    Thanked 564 Times in 367 Posts
    Holy jeeze, haven't seen one of those in a few years - ebay seems to be the haven nowadays.

  4. The Following User Says Thank You to logansryche for This Post:


  5. #3
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    Since it powers up I would sell it intact. I would put it on ebay on 10 day listing and relist it until it sold even if it took a couple months. Unless you find that parts are selling for a lot and quickly then whole is going to make you the most money. Mike
    "Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}

    Now go beat the copper out of something, Miked

  6. The Following User Says Thank You to miked for This Post:


  7. #4
    BRASSCATCHER's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Posts
    2,476
    Thanks
    3,436
    Thanked 3,965 Times in 1,383 Posts
    DO NOT part that out. I had 3 Compaq III, suitcase computers similar to what you have there. Mine had plasma screens, orange display. They are common but I got $50-$75 each for them. The ones I had powered up but had error msgs which did not allow it to get to the bios screen. If yours powers up and functions you may have a nice bit of $$$ there. Check out the Vintage Computer Forum and see if anyone can give you some info on it and if it is rare you will probably get offers on it. Nice find!!!!
    I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them.” John Wayne-- The Shootist

    NEWBS READ THIS THREAD ABOUT REFINING!!!!
    http://www.scrapmetalforum.com/off-t...ning-read.html

  8. The Following 3 Users say Thank You for This Post by BRASSCATCHER:


  9. #5
    BRASSCATCHER's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Posts
    2,476
    Thanks
    3,436
    Thanked 3,965 Times in 1,383 Posts
    That also may not be a slot proc, could be a black fibre. Where would they put the slot proc in that thing?

  10. The Following User Says Thank You to BRASSCATCHER for This Post:


  11. #6
    JustInTime started this thread.
    JustInTime's Avatar
    SMF Badges of Honor


    Member since
    May 2012
    Location
    SE Pennsy
    Posts
    192
    Thanks
    111
    Thanked 88 Times in 57 Posts
    It's laying flat under the hard drive.

    It's a slot as far as I can tell. Has the little clippy things on the top of the processor.

  12. The Following User Says Thank You to JustInTime for This Post:


  13. #7
    usurp's Avatar
    SMF Badges of Honor

    Member since
    Feb 2015
    Location
    United States
    Posts
    6
    Thanks
    1
    Thanked 8 Times in 4 Posts
    If you could can you pull off one of the keycaps and take a picture of both the switch and underneath the keycap itself? I could help identify which type of keys they are and you may be able to get a decent amount of money for the keycaps themselves!

  14. The Following User Says Thank You to usurp for This Post:


  15. #8
    JustInTime started this thread.
    JustInTime's Avatar
    SMF Badges of Honor


    Member since
    May 2012
    Location
    SE Pennsy
    Posts
    192
    Thanks
    111
    Thanked 88 Times in 57 Posts
    I threw this thing up on Ebay and almost immediately I had three best offer's asking for the keyboard alone. Grrr



  16. Similar threads on the Scrap Metal Forum

    1. Snagged off a Bonneville.. It's a BEAST- Converter
      By sledge in forum Vehicle Recycling
      Replies: 19
      Last Post: 02-05-2014, 09:52 PM
    2. Unleash the beast!
      By metallica in forum Introduce yourself
      Replies: 10
      Last Post: 12-20-2012, 04:53 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook