Results 1 to 10 of 10
  1. #1
    ozarksewaste started this thread.
    SMF Badges of Honor

    Member since
    Sep 2013
    Posts
    95
    Thanks
    0
    Thanked 84 Times in 42 Posts

    Tire glued to rim...how to remove?

    I finally got an aluminum rim from an F150...sawzalled it down to get it off only to find out that the tire is basically glued onto the rim...I'm guessing bead sealer of some sort...is there any trick to getting this unstuck or is breakage the best I can do?


  2. #2
    jimicrk's Avatar
    SMF Badges of Honor


    Member since
    Sep 2013
    Location
    Tennessee
    Posts
    2,825
    Thanks
    2,917
    Thanked 4,838 Times in 1,877 Posts
    Scroll to the bottom of the page and you will see similar threads on tire removal.

    If that don't help use the 2 search tabs at the top right and search for tire bead breaking.

    If you want to be entertained then go to youtube and type in redneck tire bead breaking.

  3. The Following 2 Users say Thank You for This Post by jimicrk:


  4. #3
    SMF Badges of Honor

    Member since
    Mar 2012
    Location
    Chesaning
    Posts
    472
    Thanks
    24
    Thanked 355 Times in 171 Posts
    Take it to the tire shop.

  5. #4
    Faceball's Avatar
    SMF Badges of Honor

    Member since
    Nov 2015
    Location
    Fingerlakes, New York
    Posts
    228
    Thanks
    996
    Thanked 354 Times in 144 Posts
    Heat, or angle grinder. Do it outside and have a bucket of water at the ready.

  6. #5
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    It's probably covered in some of the other threads.

    When i need to do a tire repair i usually remove the valve from the valve stem and let the air out. Once it's flat i run over the rubber part of the tire with my truck to break the bead seal. From there, you just use a couple of crow bars to mimic the action you get with a tire changing machine. ( It can be a booger to do with trailer tires sometimes cause they're small & tight.)

    It's probably not glue that's holding the bead. There are wire " steel belts " inside the rubber tire where the tire meets the rim. These cords stretch when you're inflating the tire to give you a really tight grip to the rim.

    If you're cutting the tire off with an angle grinder or a sawzall you have to cut those cords to get the bead to release ... if that makes any sense ?

    Kind of a smokey, stinky, messy job but sometimes that's the only way to get a shredded up tire off the rim.

    ETA: You can burn it off by tossing the whole works into a brush pile and setting it ablaze.

    The Environmental Protection Agency frowns on that kind thing but it does do a bang up job.
    Last edited by Scrappah; 05-27-2016 at 03:53 PM.

  7. #6
    CapitalRecovery's Avatar
    SMF Badges of Honor

    Member since
    Aug 2015
    Location
    United States
    Posts
    318
    Thanks
    232
    Thanked 256 Times in 134 Posts
    Bead sealer is usually made up of soapy water. It might be some kind of fixaflat. If time is money, I would take the tire to your local tire shop. If its aluminum and you want to use it for your truck, I would make sure the tire shop has a tire machine that latches from the inside of the rim and not the top. That way the bar doesn't damage the rim. Shouldn't cost you more than a couple of bucks.
    P.s. That is if the bead is still intact. If not then this message will self destruct in 30 seconds....
    29
    28
    27
    and so on.
    Last edited by CapitalRecovery; 10-28-2016 at 11:56 PM.

  8. #7
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Usa
    Posts
    763
    Thanks
    67
    Thanked 312 Times in 179 Posts
    Log splitter works great if u dotn care about the tire and rim....just be careful of alu. Alu shatters...the steel rims bend in a v. The 3 point tire crushers they sell online are just modified log splitters with 2 extra rams to bend into a triangle. Can do same with log spitter...crush...flip 180...crush...flip 90....crush..done..rims fall off.

    When short steel was higher did it all the time...cause I would still make money after paying the 1.00 tire disposal fee. For a while I dumped tires on rims..steel..off at Weitsman...they were paying 90 a gross ton in spring..now its less than 2c a lb. But still this year i ran over 80000 lbs of tires on steel rims and netted over 5 grand doing it in 3 weeks.

    Would obviously been higher if i broke down, but no time. And i had to move them quick cause junkyard was in foreclosure......3000 lbs a trip with a rented u haul trailer. After expenses i netted about 2500-3000

  9. #8
    SMF Badges of Honor


    Member since
    Jun 2014
    Location
    West Mich.
    Posts
    75
    Thanks
    6
    Thanked 43 Times in 31 Posts
    bead sealer is liquid rubber. black and sticky. it can be a pain. or someone could have actually put rtv silicone or something on it to stop a rim leak.

    either way, my tire machine will take them off no problem. if you don't have one, here's what I did before I got a machine.


    get a few cans of spray lube. get a couple tire irons. spray the bead area and let it soak for a while then start prying...keep spraying. the petroleum in the lube will soften the sealer and it will eventually move.

    the car bumper jack on the side wall supposedly works too if you've got one, slip it under a truck put the foot on the tire and jack the truck till the weight of it pops it loose...never tried it as it's easier to just do it by hand...

  10. #9
    CapitalRecovery's Avatar
    SMF Badges of Honor

    Member since
    Aug 2015
    Location
    United States
    Posts
    318
    Thanks
    232
    Thanked 256 Times in 134 Posts
    We use to call the soapy liquid that we would run around the rim Bead Sealer because it would seal the bead of a new tire we put on the rim. Maybe their are different types or that's just what they called it. My luck it was probable the later. lol

  11. #10
    Repurposer's Avatar
    SMF Badges of Honor


    Member since
    Sep 2016
    Location
    Mesa, Arizona
    Posts
    185
    Thanks
    56
    Thanked 113 Times in 69 Posts
    If it is bead sealer you can disolve it with WD-40 or the Walmart equivilant which is lots cheaper. If it's silicone good luck ever getting it cleaned off.
    Quote Originally Posted by ozarksewaste View Post
    I finally got an aluminum rim from an F150...sawzalled it down to get it off only to find out that the tire is basically glued onto the rim...I'm guessing bead sealer of some sort...is there any trick to getting this unstuck or is breakage the best I can do?




  12. Similar threads on the Scrap Metal Forum

    1. To remove or not to remove...that is the question.
      By cmgscrap in forum E-Waste Grading and Identification
      Replies: 14
      Last Post: 03-09-2014, 09:08 PM
    2. 3 min tire removal !!!!!
      By EcoSafe in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 43
      Last Post: 12-23-2013, 01:03 PM
    3. AL heat sinks glued to processors
      By Scrap man in forum Batteries, Capacitors, Heat Sinks
      Replies: 13
      Last Post: 09-28-2012, 12:45 PM
    4. Way to remove tire rims?
      By Scrap man in forum Vehicle Recycling
      Replies: 40
      Last Post: 08-29-2012, 06:48 PM
    5. Like a quarter glued to the floor at a candy store...NJ place
      By JPete in forum A Day in the Life of a Scrapper
      Replies: 10
      Last Post: 07-11-2012, 06:46 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook