Results 1 to 2 of 2
  1. #1
    Raedwyn2014 started this thread.
    Raedwyn2014's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Lehigh Valley, PA
    Posts
    21
    Thanks
    11
    Thanked 37 Times in 10 Posts

    Rear Projection Televisions - My Two Cents on How to Make a Profit!

    Hello Everyone, I hope the New Year finds everyone healthy and ready to rock 2016! With that said, here's my two cents on RPTV's:

    First, they are EVERYWHERE, so getting them free is easy. I try to charge for pickup if possible, but if not, oh well.



    I am very careful when I disassemble a Rear Projection TV...there are quite a LOT of parts to these puppies, and a few other "valuables".
    80% of the time they are in working condition, some better than others, so I test each unit to judge condition. Either way, they have about ZERO resale value, so the broken ones get disassembled just like the good ones, with the bad parts going into the appropriate recycle pile.
    With the good units here's a list of what I save:
    1.) I pull all the boards, carefully, and save them along with connection cables..I put them in a large shoe box, packed in bubble wrap, with the Name, Model, and Serial number on short side of box. I lable what boards are inside, type and part numbers, on the top of the box for inventory.
    2.) I pull the complete lamp assemblies, with boards on CRT tube complete, along with connection wires. These I box up right away, as if they were shipping tomorrow.
    3.) Speakers get pulled, labeled, and go to speaker box.
    4.) Three parts to look for - Hi Voltage Splitter Assembly, Resistor, High Voltage, and High Voltage Divider. These items sell for me quite often, for between $35.00 and $75.00!
    5.) Projection Television Control Panel Button Assembly - these seem to break or wear out, and sell pretty well also.
    6.) Rear Projection Mirror assembly.
    7.) Fresnel lens, along with plexi Screen.
    8.) Casters on bottom of cabinet - if it has any, pull them - they are usually high quality.
    9.) The Remote! They usually sell for @ $15.00 to $35.00, and are always in demand.

    PRO TIP - ALWAYS TAKE A PICTURE OF THE MODEL/SERIAL NUMBER, ETC., USUALLY ON STICKER SOMEWHERE INSIDE CABINET!
    PRO TIP II - I ALWAYS TRY TO FIND FREE PDF FILES OF PARTS MANUAL AND SERVICE MANUAL - I HAVE A SPECIFIC FOLDER ON MY LAPTOP FOR THESE.

    Lastly, depending on cabinet type, I make all kinds of stuff; The big wooden cabinets, after being gutted, have been made into a.) a rolling workshelf - just add some shelves, put a smooth plywood top over wood grain particle board for workspace! b.) after wood cabinet has been gutted, put a thin sheet of luan, or heavy cardboard, to cover back opening. I tack some felt along the inside walls, and a nice basket and fitted cushion on the bottom (I have a buddies wife who can make a custom cushion), and "viola", a custom high grade inside dog house for your favorite pooch. I sold one of these for $125 bucks one time, and gave the workbench to my mechanic for letting me use his shop.

    With the prices of scrap living below the turds in the crapper, reselling parts, and repurposing stuff is the way to go...I sold a complete lamp assembly (3 lamps w/boards on end) for $325, and shipped it to Moose Jaw, Saskatchewan...shipping alone was $175, paid by customer!

    It doesn't take long to get used to what's what inside these beasties, and the leftover scrap is usually a little ABS plastic, on maybe some aluminum or steel framing, along with TONS of hardware (screws, bolts, washers, springs, brackets) that all go in the hardware bucket.

    Any questions - hit me up. Any ideas to do it better, let me know - there's always a better way to catch a mouse!
    Happy Scrapping Guys - with prices in the ****ter, I'm looking forward to an awesome year, just gonna do things differently!
    Scrap on, me hearties!

  2. The Following 3 Users say Thank You for This Post by Raedwyn2014:



  3. #2
    AuburnEwaste's Avatar
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Metro Detroit
    Posts
    773
    Thanks
    32
    Thanked 976 Times in 413 Posts

    Rear Projection Televisions - My Two Cents on How to Make a Profit!

    We do these all the time. I always charge to pick up but drop off is free. I used to hate them but I have an employee to take them apart for me now.

  4. The Following User Says Thank You to AuburnEwaste for This Post:



  5. Similar threads on the Scrap Metal Forum

    1. rear projection TV.
      By EcoSafe in forum General Electronics Recycling
      Replies: 16
      Last Post: 04-30-2015, 11:50 PM
    2. Replies: 51
      Last Post: 02-17-2015, 06:57 PM
    3. Scrapping a Rear Projection
      By mtnman81 in forum Scrap Metal Tips and Advice
      Replies: 8
      Last Post: 07-03-2013, 07:57 AM
    4. Rear projection televisions
      By Gripandflip in forum General - Let's talk business
      Replies: 3
      Last Post: 11-15-2011, 01:13 AM
    5. What all do I have to discharge on a rear projection TV?
      By zakmattingly in forum Scrap Metal Questions and Answers
      Replies: 21
      Last Post: 07-17-2011, 01:12 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook