Results 1 to 7 of 7

Switching fuel for Oxy cutting

| Tools and Equipment
  1. #1
    JnJunk started this thread.
    JnJunk's Avatar
    SMF Badges of Honor

    Member since
    Oct 2014
    Posts
    188
    Thanks
    34
    Thanked 109 Times in 59 Posts

    Switching fuel for Oxy cutting

    I picked up a torch set up at an auction from one of the gas suppliers by me. I've went and got the oxy and acetylene filled and it was over 100 bucks for the two little tanks. I just about passed out right there. At that price I cannot even afford to fire up the torch.

    So I got thinking, Theres another gas supplier down the street from me. Supposedly the prices are a heck of a lot better. I was going to get a quote on a 125cf oxy tank and switch my fuel gas to propane. Supposedly you can just switch the hoses and torch tip and start cutting with propane. I'm wondering if this is true? I know there are a lot of industrial scrap guys on here.



  2. #2
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,589
    Thanked 7,220 Times in 2,256 Posts
    I have a little experience with torches, cutting with gasoline, diesel, propane, natural gas, plasma cutters, and acetylene. The information you were given is partially correct. All you have to change is the torch tip. Propane is cheaper and far more efficient than acetylene for scrapping. The secret is setting the flame correctly. It should sound like a jet engine when set and produce a defined and sharp star when the flame is held within 3/4 in. of flat metal.

    Using the largest oxygen tank reduces the cost per cu. ft. A single K tank of oxygen will last about 2 hrs. of steady hard cutting. The propane tank from a grill will last for a long time. I use 100 lb. propane tanks and liquid oxygen (equal to 17 K tanks) and with this set up estimate that I spend about $ 3.00 per hour on fuel. Using oxygen K tanks the cost for fuel is about $ 8.00 per hour. These figures assume proper regulator settings and good cutting technique. The only cheaper fuel I have found is gasoline and this requires a special torch. Hope this helps.
    Give back more to this world than we take.

  3. The Following 5 Users say Thank You for This Post by Patriot76:


  4. #3
    JnJunk started this thread.
    JnJunk's Avatar
    SMF Badges of Honor

    Member since
    Oct 2014
    Posts
    188
    Thanks
    34
    Thanked 109 Times in 59 Posts
    It does help. So from your experience an acetylene regulator will handle the propane? Someone was telling me I had to change the orifices inside the regulator. I have probably about a dozen 20lb propane tanks sitting around so I figured I might as well use them for something. I have to go get a quote for a tank, My friend down south of me says he pays 20 bucks a cylinder for oxygen

  5. #4
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,589
    Thanked 7,220 Times in 2,256 Posts
    Quote Originally Posted by JnJunk View Post
    It does help. So from your experience an acetylene regulator will handle the propane? Someone was telling me I had to change the orifices inside the regulator. I have probably about a dozen 20lb propane tanks sitting around so I figured I might as well use them for something. I have to go get a quote for a tank, My friend down south of me says he pays 20 bucks a cylinder for oxygen
    Yes and inaccurate information

  6. The Following User Says Thank You to Patriot76 for This Post:


  7. #5
    DiamondN's Avatar
    SMF Badges of Honor


    Member since
    Oct 2012
    Location
    Indiana
    Posts
    912
    Thanks
    2,150
    Thanked 378 Times in 243 Posts
    I ran the small 'grill' size tanks a few years ago to save some bucks, and they worked out pretty nice. The only thing that I had to change was the cutting tip itself. Everything else remained the same. The 'pros' were: lower operating costs and tanks could be exchanged or refilled almost everywhere, which also translates into lower costs. The 'cons' were: It seemed the propane wouldn't get as 'hot' as when using acetylene.

  8. The Following User Says Thank You to DiamondN for This Post:


  9. #6
    scrapman1077's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    Alabama
    Posts
    76
    Thanks
    5
    Thanked 79 Times in 32 Posts
    I have used Oxy-Propane for cutting for 30 years, only the tip has to be changed.

  10. The Following User Says Thank You to scrapman1077 for This Post:


  11. #7
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,589
    Thanked 7,220 Times in 2,256 Posts
    Although the pictures have been deleted compliments of photo bucket, some of the information is valuable.

    https://www.scrapmetalforum.com/tool...crappers+dream

  12. The Following 3 Users say Thank You for This Post by Patriot76:



  13. Similar threads on the Scrap Metal Forum

    1. Fuel from air
      By Otto in forum Off Topic Discussions
      Replies: 0
      Last Post: 11-10-2016, 08:58 AM
    2. Bio Fuel
      By Catfish Bob in forum Non Metal Recycling
      Replies: 2
      Last Post: 08-10-2014, 08:00 PM
    3. Switching gears a bit
      By BRASSCATCHER in forum A Day in the Life of a Scrapper
      Replies: 20
      Last Post: 01-09-2013, 03:33 PM
    4. Switching from Windows to Linux
      By billygoat in forum Off Topic Discussions
      Replies: 23
      Last Post: 12-07-2012, 04:26 PM
    5. Switching gears for the summer
      By BRASSCATCHER in forum General - Let's talk business
      Replies: 10
      Last Post: 06-10-2012, 01:00 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook