Results 1 to 18 of 18

the art of stripping braided wire

| Misc. Metal Recycling
  1. #1
    Dumpster-Dee started this thread.
    Dumpster-Dee's Avatar
    SMF Badges of Honor



    Member since
    Feb 2011
    Location
    SW Georgia
    Posts
    1,775
    Thanks
    2,286
    Thanked 838 Times in 457 Posts

    the art of stripping braided wire

    Stripping braided wire can be a real challenge. But I am stubborn, and I've stayed with it until I have succeeded enough to make me want to keep on until I have it mastered !! Thanks to those of you more experienced guys who've given me tips and encouraged me.

    Here are some important factors I've learned and wanted to share with others who've gotten discouraged and maybe even given up:



    First, your utility blade must be very sharp (and when you're learning it gets dull fast as you hit the wire!!)

    Second, you must pull tightly so the wire is taunt...(I put one end in my vise and pull the wire tight with my gloved hand or pliers)

    Third, it's the angle of the blade that is the key...and in this case only practice will enable you to succeed.

    Fourth, practice only on clean wire. If you practice on aged, brittle, lamp wires, you'll never succeed. This is another variable to consider when stripping any wire, and only comes with practice; but is especially pertinent when considering braided wire.

    Fifth, another variable is the sheathing itself....as you know all sheathing is not created equal....so some will be easier to strip than others....so again.... practice is the only solution.

    And, did I mention.....practice. You'll be glad you did. I know I am. But I'll also be happy to order that $200 stripper from Sweden as soon as the other bills leave me a $200 surplus !!

    Dee

  2. The Following 14 Users say Thank You for This Post by Dumpster-Dee:



  3. #2
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    I don't know what kind of utility blade you use, but I found something at Harbor Freight you might want to consider. They have what looks like a folding clasp knife that uses the blades from box cutters. Just press the button down on the knife and the blade slips right out and you can turn it around and use the other side. It comes with 5 blades in the package. Price: 6.99. I also bought a box of 100 blades for 2.99. Using their common 20% off on the knife I got the whole kit and kaboodle for under 10 buck, including tax. I use the newer blades to strip the insulated wire with, and when the blade gets too dull to effectively strip the insulation, I replace it but keep it as it is still sharp enough to cut plastics and tapes bundling the wire together, or anything else I need to cut. And then, like everyone else here, when it gets too dull for any cutting, like all my other worn out tools, goes in the steel scrap pile. I love doing something where there is relatively little waste!!

  4. The Following 2 Users say Thank You for This Post by wayne1956:


  5. #3
    SMF Badges of Honor


    Member since
    Jun 2011
    Posts
    139
    Thanks
    59
    Thanked 13 Times in 9 Posts
    Braided wire and me = gasoline lol

  6. The Following User Says Thank You to MilitiaMetals for This Post:


  7. #4
    SMF Badges of Honor


    Member since
    May 2011
    Posts
    187
    Thanks
    12
    Thanked 63 Times in 29 Posts
    One other tip is to get it as straigt as you can when you strip it. Everytime you hit a kink or bend in the wire it changes the blade angle and digs in.

    I can strip most braided wire just as fast as solid. The real fine stranded wire that isn't braided is a PITA though.

  8. #5
    Dumpster-Dee started this thread.
    Dumpster-Dee's Avatar
    SMF Badges of Honor



    Member since
    Feb 2011
    Location
    SW Georgia
    Posts
    1,775
    Thanks
    2,286
    Thanked 838 Times in 457 Posts
    Just discovered titanium blades....love 'em. Did I mention PRACTICE !!!???

  9. The Following 3 Users say Thank You for This Post by Dumpster-Dee:


  10. #6
    SMF Badges of Honor

    Member since
    Dec 2011
    Location
    Shenandoah Valley
    Posts
    6
    Thanks
    12
    Thanked 11 Times in 4 Posts



    I use an old Stanley hand planer (top in the above image),for the braided, the blade is adjustable, so I just set the depth and lay the cord on an old cutting board and slide right across the length of the wire. It took a bit to get used to but now it's a no brainer for me..

    for the smaller diameter I use the 2x4 with the holes and screws and muscle them through.. I would give credit here but I am sure you know the member who posted that video..

  11. The Following 5 Users say Thank You for This Post by WhiteLightning:


  12. #7
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Dee, thanks for starting this thread! Can I ask - do you heat the wire in any way?
    Success consists of going from failure to failure without a loss of enthusiasm...... Churchill

  13. #8
    Dumpster-Dee started this thread.
    Dumpster-Dee's Avatar
    SMF Badges of Honor



    Member since
    Feb 2011
    Location
    SW Georgia
    Posts
    1,775
    Thanks
    2,286
    Thanked 838 Times in 457 Posts
    Nope...if I got any faster it would scare me !!

  14. The Following User Says Thank You to Dumpster-Dee for This Post:


  15. #9
    sars101's Avatar
    SMF Badges of Honor


    Member since
    Jan 2012
    Location
    texas
    Posts
    32
    Thanks
    21
    Thanked 7 Times in 4 Posts
    i been using the blade method
    I like the wood planer idea.
    any one tried using a razor on thin wires?

    ok what should I do here

    what's that wire to the left is it aluminum its none magnetic.
    and theirs foil paper all along the wire. anyone no a faster way to take it a part other then using a blade?
    Quote Originally Posted by tigerbeetle View Post
    ” Ryan said.
    She also noted that she had gone to the local Family Dollar store and there was only one shopping cart. “I asked the manager and she told me they had 20 but 19 had been taken.” The carts were made of metal.

  16. #10
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    I personally don't mess with stuff that small, I sell as insulated.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  17. #11
    sars101's Avatar
    SMF Badges of Honor


    Member since
    Jan 2012
    Location
    texas
    Posts
    32
    Thanks
    21
    Thanked 7 Times in 4 Posts
    ok thanks but don't I have to take off the first insulatedcover?

  18. #12
    RustyDollars's Avatar
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Central Wis
    Posts
    426
    Thanks
    438
    Thanked 533 Times in 213 Posts
    Quote Originally Posted by WhiteLightning View Post



    I use an old Stanley hand planer (top in the above image),for the braided, the blade is adjustable, so I just set the depth and lay the cord on an old cutting board and slide right across the length of the wire. It took a bit to get used to but now it's a no brainer for me..
    Ha! And hear I thought that I was the only one using a Stanley block plane. For me it's much-much faster than a knife on braided wire.

  19. #13
    Dumpster-Dee started this thread.
    Dumpster-Dee's Avatar
    SMF Badges of Honor



    Member since
    Feb 2011
    Location
    SW Georgia
    Posts
    1,775
    Thanks
    2,286
    Thanked 838 Times in 457 Posts
    one of you should make a video

  20. The Following User Says Thank You to Dumpster-Dee for This Post:


  21. #14
    SMF Badges of Honor

    Member since
    Jan 2012
    Location
    Barry Co. Michigan
    Posts
    7
    Thanks
    12
    Thanked 3 Times in 2 Posts
    Sars101,

    For the thin wire I placed a single edge razor blade in a 1 x 4 board with a hole in it & mounted in my vice. With the 4 " side facing you, drill a
    hole a little bigger in diameter than your insulation about inch from the top. Then cut down through the center of the hole
    with a narrow saw. Tap the razor blade down so the edge is in the top of the hole. I use a c clamp at the top of the board
    to tighten the slot and hold the blade in it. For set up I will strip the first inch of insulation off and feed it thru the hole. I tap
    the front of the blade down till it hits the insulation above the copper, then tighten the clamp, and pull the wire thru. It takes a
    little to get it right but once set you a good for that diameter wire. You can add larger holes below the first one and extend the slot
    for larger wires. Remember the insulation on thin wire is not thick, you only have to score it good to be able to pull the wire out.
    Can't that credit for this. I dummy downed a version of a home made wire stripping machine I saw on you tube.
    Have Fun

  22. The Following 2 Users say Thank You for This Post by Luner5:


  23. #15
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts

    You mean this one???

  24. The Following User Says Thank You to Mechanic688 for This Post:


  25. #16
    SMF Badges of Honor

    Member since
    Feb 2012
    Location
    burbank ca
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Thanks for sharing your valuable tips on stripping braided wire here at http://www.scrapmetalforum.com

  26. #17
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Illinois
    Posts
    4
    Thanks
    0
    Thanked 3 Times in 2 Posts
    (it wont let me post links, i am refering to whitelightnings picture)

    I saw somewhere on here a while ago a guy talking about using a planer so i gave it a shot yesterday and i think its going to work great. I have the same one as in the bottom of the above picture whitelightning posted. I turn it upside down and clamped it flush to a bench i have. I am still figuring out the best method but it has worked pretty good just pulling the wire on one end and keeping pressure on the other end by the planer with my palm. Still tinkering though. Anyways thanks to whoever originally posted the planer method, whitelightning maybe?

  27. #18
    Abuilder's Avatar
    SMF Badges of Honor


    Member since
    Apr 2012
    Location
    SE Wisconsin
    Posts
    436
    Thanks
    228
    Thanked 487 Times in 251 Posts
    This sounds kinda crazy but it works for me on stranded, braided and really most type of wire insulation.
    An antique stainless steel potato peeler. I hold the peeler firmly on top of my vise and run the wire under it.
    This one is just like mine.
    http://www.lefsetime.com/store/produ..._Peeler214.jpg

  28. The Following User Says Thank You to Abuilder for This Post:



  29. Similar threads on the Scrap Metal Forum

    1. stripping copper wire vs non stripping-my opinion.
      By vamped400 in forum Scrap Metal Tips and Advice
      Replies: 13
      Last Post: 07-04-2016, 02:07 AM
    2. Computer Power Cables - Unshielded wire braided with copper?
      By scrap1025 in forum Scrap Metal Questions and Answers
      Replies: 6
      Last Post: 03-11-2013, 11:23 AM
    3. Burning wire vs stripping wire?
      By TheFatMan in forum Scrap Metal Tips and Advice
      Replies: 44
      Last Post: 07-15-2012, 02:30 AM
    4. Lighting Rod Braided Copper Wire
      By gustavus in forum Scrap Metal Spots
      Replies: 5
      Last Post: 09-29-2011, 02:38 AM
    5. Stripping Wire
      By WHIscrapping in forum Tools and Equipment
      Replies: 7
      Last Post: 03-15-2011, 11:46 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook