Page 1 of 2 12 LastLast
Results 1 to 20 of 23

Anything valuable in washers/ dryers?

| Scrap Metal Questions and Answers
  1. #1
    Scrap man started this thread.
    Scrap man's Avatar
    SMF Badges of Honor

    Member since
    Nov 2010
    Location
    NY
    Posts
    657
    Thanks
    36
    Thanked 172 Times in 93 Posts

    Anything valuable in washers/ dryers?

    So I have a washer and dryer I'm bringing to the scrapyard tomorrow and I was just wondering if there's anything valuable in them like brass, aluminum, copper, etc. I also heard there were circuit boards in some of them. Is this true?



  2. #2
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    I've wondered the same. I would at least remove the cord and motor. I think the drums are stainless.

  3. #3
    Scrap man started this thread.
    Scrap man's Avatar
    SMF Badges of Honor

    Member since
    Nov 2010
    Location
    NY
    Posts
    657
    Thanks
    36
    Thanked 172 Times in 93 Posts
    I was thinking that too

  4. #4
    tjlock's Avatar
    SMF Badges of Honor



    Member since
    Sep 2010
    Location
    Central Illinois (Streator)
    Posts
    188
    Thanks
    9
    Thanked 37 Times in 20 Posts
    I have taken apart a few washers and 1 dryer. There are insulated copper wires inside that add up. Coming in at the plug entrance and down to the motor. Should have wires going to different dials on the machines. For the dryer, check the trap, may find change or other items that might be valuable. The washer should have a few brass fittings in it maybe the dryer to around dials. The dryer I had was apparently steel. Magnet stuck to the one I had.

  5. #5
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    Tore apart my first dryer yesterday. Pulled the wire and motor. Drum is steel - painted. I looked inside my home dryer and it's stainless. When it gives up I am definitely tearing that one apart. The faceplate is aluminum so I pulled that, but it's so light it will take a lot to make any weight.

    Also pulled the heating elements. A magnet wouldn't stick but I don't know what it is.

  6. #6
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    Generally all I do with washers and dryers is remove the wiring harness (insulated copper), and if it is not too difficult, the electric motor. Most everything after that is not really worth messing with. One thing to also watch out for is quite often in dryers you can find change in the bottom of the dryer. I have found as much as $17 and one heavy silver chain in one dryer. My last dryer I processed weekend before last gave up just short of $2 in change. Also watch out for brass fittings in gas dryers.

  7. #7
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    Tore apart another dryer. Found a black thong jammed in the blower housing, and 57 cents. The lady did say the drum quit turning. I am guessing this is why. Should I see if she wants her panties back? haha.
    Attached Images Attached Images  

  8. The Following 3 Users say Thank You for This Post by IdahoScrapper:


  9. #8
    SMF Badges of Honor

    Member since
    Dec 2010
    Location
    Miles City, MT
    Posts
    158
    Thanks
    50
    Thanked 27 Times in 21 Posts
    Always good to use pliers to remove thongs who knows hwere they have been lol

  10. #9
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    $.78 in change in the one I found today no thong!!

  11. #10
    Scrap man started this thread.
    Scrap man's Avatar
    SMF Badges of Honor

    Member since
    Nov 2010
    Location
    NY
    Posts
    657
    Thanks
    36
    Thanked 172 Times in 93 Posts
    You just had to include a picture... And I just had to click it. Lol
    There's nothing more fun and more effective than hitting something repeatedly with a sledgehammer

  12. #11
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    lol. If I come across anything again, I'll try to remember to include a warning.

  13. #12
    Rusty Nuts's Avatar
    SMF Badges of Honor


    Member since
    Jan 2011
    Location
    Texas
    Posts
    86
    Thanks
    6
    Thanked 26 Times in 11 Posts
    I found a small silver necklace with the name "Laquiesha" on it.

    In answer to the OP- between the heavy duty copper wire and the huge motor (and the spare change) I think you could double the dollar amount over just selling it as light tin or white goods.
    Last edited by Rusty Nuts; 01-28-2011 at 11:24 AM.

  14. #13
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    Anyone know if the stuff attached to the control panel is worth keeping separate? For now I've been pulling the wires and letting the panel go, but there's some weight to it and haven't investigated what all is in there.

  15. #14
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    Quote Originally Posted by IdahoScrapper View Post
    Anyone know if the stuff attached to the control panel is worth keeping separate? For now I've been pulling the wires and letting the panel go, but there's some weight to it and haven't investigated what all is in there.
    I personally cannot think of anything other than the sheet metal it is attached to. Normally it is aluminum, so I will remove it, pull the outside knobs off and the circuitry inside, then I have my sheet aluminum. I naturally do the magnet test before doing this.

  16. #15
    ScrapperNJ26's Avatar
    SMF Badges of Honor


    Member since
    Jan 2011
    Location
    Clementon NJ
    Posts
    512
    Thanks
    537
    Thanked 148 Times in 89 Posts
    I pulled apart a dryer yesterday found a $20 Bill and about $16 in change. I was wondering.......has anyone contacted laundromats? What happened?

  17. #16
    SMF Badges of Honor


    Member since
    Jan 2011
    Posts
    40
    Thanks
    4
    Thanked 5 Times in 5 Posts
    so far i have scrapped two dryers and not found one thing..

  18. #17
    SMF Badges of Honor


    Member since
    Jan 2011
    Posts
    40
    Thanks
    4
    Thanked 5 Times in 5 Posts
    some have aluminum pieces.. check with your magnet. The piece you will get weighs nothing though.. do it if you are in no rush. if time is important, its not worth it..

  19. #18
    Rusty Nuts's Avatar
    SMF Badges of Honor


    Member since
    Jan 2011
    Location
    Texas
    Posts
    86
    Thanks
    6
    Thanked 26 Times in 11 Posts
    Quote Originally Posted by azscrapper View Post
    so far i have scrapped two dryers and not found one thing..

    I'll send you the "Laquiesha" necklace if it'll help.

    There are at least 2 spots where I found change inside the dryer I did.
    On the bottom of the dryer- along the outside edges, and also in the duct right above the fan blades.

  20. #19
    SMF Badges of Honor


    Member since
    Jan 2011
    Location
    Columbus, IN
    Posts
    204
    Thanks
    18
    Thanked 75 Times in 26 Posts
    Well at least the thong should have already been through the washer, that would be some consolation ROFL

  21. #20
    Scrap man started this thread.
    Scrap man's Avatar
    SMF Badges of Honor

    Member since
    Nov 2010
    Location
    NY
    Posts
    657
    Thanks
    36
    Thanked 172 Times in 93 Posts
    Quote Originally Posted by Rusty Nuts View Post
    I'll send you the "Laquiesha" necklace if it'll help.

    There are at least 2 spots where I found change inside the dryer I did.
    On the bottom of the dryer- along the outside edges, and also in the duct right above the fan blades.
    There's sometimes change in the water pumps. There's also usually a few cents in the tubing.


  22. Similar threads on the Scrap Metal Forum

    1. Selling Washers and Dryers for more $$$$$$
      By BigRyan in forum More than Scrap Value
      Replies: 13
      Last Post: 12-06-2014, 09:53 AM
    2. washers and dryers
      By GeorgeB in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 33
      Last Post: 07-10-2013, 08:02 AM
    3. 2 washers gets me...
      By Scrappy22 in forum Scrap Metal Prices
      Replies: 6
      Last Post: 04-29-2013, 10:04 AM

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 4 users browsing this thread. (0 members and 4 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook