Search:

Type: Posts; User: blackgold12; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    640

    https://youtu.be/9g_-xOyW2H0

    https://youtu.be/9g_-xOyW2H0
  2. Replies
    107
    Views
    10,399

    https://youtu.be/WCcLMNcWZOc

    https://youtu.be/WCcLMNcWZOc
  3. Replies
    16
    Views
    640

    The insulators inside of the magnetron are made...

    The insulators inside of the magnetron are made of beryllium,

    DO NOT risk the chance of getting sick with Berylliosis (beryllium disease) because you scratched the insulation!
    ...
  4. Someone has a decent camera, a nice sharp image...

    Someone has a decent camera, a nice sharp image of a cpu with a bit of unnecessary clutter.

    I think the photographer needs a bit of instruction on how to take a photo leaving the clutter out.
  5. Like they say the early bird gets the worm.

    Like they say the early bird gets the worm.
  6. These drive shaft parts are useful for projects,...

    These drive shaft parts are useful for projects, for the go cart steering I had cut two ears off the spider then welded the axle stub onto the center. Doing similar have used these as hinges on farm...
  7. Replies
    47
    Views
    3,364

    Hills when you have time post a picture of your...

    Hills when you have time post a picture of your Yanmar clone crankshaft taper.
  8. My kids tooled around on Honda 50 cc motorcycles,...

    My kids tooled around on Honda 50 cc motorcycles, neat little bikes three speed transmission with automatic clutch, I made them a go cart on turf tires powered with 5 horse Briggs.

    Those little...
  9. Replies
    47
    Views
    3,364

    Hills search for the appropriate kilowatt two...

    Hills search for the appropriate kilowatt two bearing generator to suit your Yanmar clone's horse power then with one of these adapters you'll be able to put your diesel engine back to work.
    ...
  10. Replies
    47
    Views
    3,364

    Don't assume anything about crankshaft tapers...

    Don't assume anything about crankshaft tapers used for generator armatures being the same, I know for a fact Onan uses different taper on their RV gen sets.

    Maybe its possible the Chinese copied...
  11. Is it cold enough outside to freeze any water...

    Is it cold enough outside to freeze any water left in the pump that would keep it from turning over.
  12. Replies
    47
    Views
    3,364

    IMO finding a good used 10 horse power Tecumseh...

    IMO finding a good used 10 horse power Tecumseh generator engine is no easy task, you might have to swap the crankshaft from your damaged engine into the new one so you have the tapered shaft for the...
  13. Replies
    47
    Views
    3,364

    My generators and those used on Miller Big 40's...

    My generators and those used on Miller Big 40's and Lincoln have armatures large enough that they use a flex plate to attach the armature to the flywheel surface.
    ...
  14. Replies
    47
    Views
    3,364

    Thought we were going to repair or replace the...

    Thought we were going to repair or replace the armature, it your scraping for copper just beat on it with a large sledge hammer after the retaining bolt has been removed.
  15. Thread: Hi All!

    by blackgold12
    Replies
    9
    Views
    725

    Before you start dismantling your 20 year old...

    Before you start dismantling your 20 year old electronics make sure it don't have collector value. before destroying anything.

    https://i.postimg.cc/2ynXs4s8/woz.png
  16. Replies
    47
    Views
    3,364

    Same trick is used to remove a pilot bearing from...

    Same trick is used to remove a pilot bearing from the end of crankshaft only we use grease then hammer in a tapered wood plug, the guy removing the armature in the video could have used slide hammer...
  17. Replies
    47
    Views
    3,364

    Had a similar Vanguard mine was a light blue, a...

    Had a similar Vanguard mine was a light blue, a few Vauxhall's with the inline 6 cylinder and then when I met my wife to be had a Vauxhall wagon.

    I rolled the wagon coming down a mountain, with...
  18. Screen capture

    Screen capture
  19. Replies
    4
    Views
    1,307

    Screen capture

    Screen capture
  20. Replies
    9
    Views
    13,528

    Sticky: Read this before posting your spam again, the...

    Read this before posting your spam again, the CRTC stands for the Canadian Radio and Television Commission.

    You may not be aware, I'm Canadian and you crap knows no boundary's, your posting your...
  21. Replies
    6
    Views
    573

    This thead is a question - The performance of the forum as a revenue...

    The performance of the forum as a revenue generator in its current state is definitely not blue chip, but I believe as many others do that under proper management this site could this site could...
  22. Replies
    6
    Views
    573

    This thead is a question - If this helps, out of curiosity I requested an...

    If this helps, out of curiosity I requested an evaluation report,

    scrapmetalforum.com Traffic Worth

    We estimate the website value of scrapmetalforum.com is currently at $ 4,525 USD and...
  23. Replies
    6
    Views
    573

    This thead is a question - I think all tickets requests are going into a...

    I think all tickets requests are going into a dead letter drop box.

    If something is bothering you spit out publicly on the forum and we'll sort it out for ya.
  24. Replies
    3
    Views
    3,795

    National - Probably have to pay a finder fee to get that...

    Probably have to pay a finder fee to get that information.
  25. Replies
    47
    Views
    3,364

    It's because of their bulk, for instance the...

    It's because of their bulk, for instance the Petter PJ at a measly 20 horse power the engine weighs 550 pounds the crankcase would have been cast useing one alloy formula while the cylinder from a...
Results 1 to 25 of 288
Page 1 of 12 1 2 3 4

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook