Search:

Type: Posts; User: mthomasdev; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    1,057

    4438 Use this chart to figure recovery. ...

    4438

    Use this chart to figure recovery.

    Once you get to 1/0, the wire gets bigger as you increase in number. It goes 1/0 thru 4/0 and then into the mcm or kcm or kmil.
  2. Replies
    18
    Views
    1,533

    A lot of these types of machines will have a...

    A lot of these types of machines will have a mechanism that will reverse the spin. I assume there is some sort of sensor that detects when there is a jam.
  3. Replies
    1,992
    Views
    544,970

    National - Thank you! You should look at the "any thoughts"...

    Thank you! You should look at the "any thoughts" thread.
  4. Replies
    1,992
    Views
    544,970

    National - Please clarify PSU with wires. Seems that your...

    Please clarify PSU with wires. Seems that your scale guy told a member that the metal case must be removed. Thank you.
  5. Replies
    50
    Views
    2,631

    If I have to go thru the trouble of taking them...

    If I have to go thru the trouble of taking them out out the steel, then I'm cutting the wire off and selling the boards as power supply boards at at least 30 to 35 cents.
  6. Let me start by saying I don't have a system, but...

    Let me start by saying I don't have a system, but have a good knowledge of them. I sell to a company that processes alot of wire and other copper bearing material. They build thier own equipment...
  7. Replies
    50
    Views
    2,631

    What do you mean that you need to take the steel...

    What do you mean that you need to take the steel off. Never done that on a shipment of PSUs. They go thru the hammer mill as is.
  8. Replies
    3
    Views
    681

    That wire is typically considered 82 percent...

    That wire is typically considered 82 percent recovery. Your numbers are very close for a small amount. Most likely your scale only goes to a tenth of an ounce. Recovery does go up a little as you...
  9. Another thing that can mess up a day's run, is...

    Another thing that can mess up a day's run, is not realizing there was some tin coated copper wire in the mix. That load on #1 is now #2.
  10. Replies
    50
    Views
    2,631

    Not so much that you are on the end of the...

    Not so much that you are on the end of the freight line, it's more that there are no national carriers. You wind up paying 2 different carriers, each who want to make a profit.
    Something I found...
  11. Replies
    50
    Views
    2,631

    Pallets are easy to find. Get small boxes from...

    Pallets are easy to find. Get small boxes from home Depot. Do a dry run building your stack of boxes on the pallet. Buy a roll of plastic wrap from Home Depot. Bring all this to the terminal and...
  12. Replies
    50
    Views
    2,631

    Just goes to show everyone that volume talks. ...

    Just goes to show everyone that volume talks. This goes for selling as well as shipping. If you have quantity when selling, don't be afraid to ask for more or even throw other prices around. You'd...
  13. Replies
    50
    Views
    2,631

    Ran 1000 pound pallets 40x48x40. Single was...

    Ran 1000 pound pallets 40x48x40. Single was 128.18. 2 to 6 pallets was running about $90.50 per pallet. Billings to oakwood village.
  14. Replies
    50
    Views
    2,631

    Prices I listed where Knoxville TN to oakwood...

    Prices I listed where Knoxville TN to oakwood village, oh. Dropped at terminal, same company I used to ship to you in Billings. Give me some estimated weights and dimensions and I'll punch it in if...
  15. Replies
    50
    Views
    2,631

    128.18 1000 pound 40x48x40 dropped off 37921 ...

    128.18 1000 pound 40x48x40 dropped off 37921

    Believe it or not, 2 of those boxes is 125 and change.
  16. Replies
    50
    Views
    2,631

    Where are you in Tennessee? Shipping those PSUs...

    Where are you in Tennessee? Shipping those PSUs shouldn't be too bad? Do you know the weight of that Gaylord and dimensions? Do you have a way of getting it to a freight terminal. If you do, I'll...
  17. Wisconsin | National - I can confirm that a text message was received...

    I can confirm that a text message was received and a decent size payment was received thru PayPal. At this point, I have not received a list of our complete transaction with various purchase prices,...
  18. Wisconsin | National - So I have been holding off on posting this,...

    So I have been holding off on posting this, hoping there would be a better outcome and I could say that TJ fully paid me, but that is not the case.
    I sent roughly 300 'i' series laptops and over 300...
  19. Replies
    15
    Views
    1,934

    Who do I write the check to and where do I send...

    Who do I write the check to and where do I send it?
  20. Replies
    16
    Views
    3,429

    Looks like a C4 turbo deluxe with a single shaft...

    Looks like a C4 turbo deluxe with a single shaft shredder in place of a dual shaft shredder.
  21. Replies
    16
    Views
    3,429

    Going back to your first post, I'd guess they...

    Going back to your first post, I'd guess they quoted you a C4 system.
  22. Replies
    16
    Views
    3,429

    I believe they have customers running acr with a...

    I believe they have customers running acr with a C1 setup. Those are in the 50k range. Would probably add a single shaft shredder with a conveyor and mag belt. That would probably put you in the...
  23. Replies
    16
    Views
    3,429

    The mini is in the 25 to 30 range. C1 about 50...

    The mini is in the 25 to 30 range. C1 about 50 and C2 about 80. They had a used C2 available a couple weeks ago. Think they were asking 52.
  24. Replies
    16
    Views
    3,429

    Take a look at a system from cable management in...

    Take a look at a system from cable management in Meriden CT. Very efficient systems. I sell wire to them and have had tours of his plant. You could also try to contact SMF member Missouri,. Roy...
  25. Replies
    51
    Views
    53,826

    I think you better tell us who is paying $4 to $7...

    I think you better tell us who is paying $4 to $7 for motherboards. I'm sure I'm not the only one that will want to run a few thousand pounds of motherboards down there before they either smarten up...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook