Results 1 to 5 of 5
  1. #1
    BoardSort started this thread.
    BoardSort's Avatar
    SMF Badges of Honor

    Member since
    Jun 2011
    Location
    Eastlake, Ohio
    Posts
    5
    Thanks
    2
    Thanked 13 Times in 5 Posts

    How to remove a hard drive board FAST!

    The fastest way to remove a hard drive board is to pry the board from the drive using a stout but sharp flat head screwdriver. #NoScrewingAround



    -------------------------------------------------------------
    -> Chris Skeeles - Buyer at Large - Boardsort.com <-
    -------------------------------------------------------------

  2. The Following User Says Thank You to BoardSort for This Post:



  3. #2
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,415
    Thanks
    1,109
    Thanked 1,028 Times in 563 Posts
    I prefer to actually use the screw driver for its intended purpose. Thats a easy way to crack the board.

    Edit for balligerance, polligise...
    Last edited by greytruck; 05-08-2019 at 12:30 PM. Reason: non sence

  4. #3
    mikeinreco's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    TENNESSEE
    Posts
    4,114
    Thanks
    1,104
    Thanked 4,299 Times in 1,949 Posts
    After doing tens of thousands I agree that the proper bit and an impact screwdriver is the best and fastest way to remove the boards from the desktop hd's....I do use the prying method for the laptop hd's

  5. The Following User Says Thank You to mikeinreco for This Post:


  6. #4
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,313
    Thanks
    2,278
    Thanked 2,262 Times in 1,097 Posts
    How is the board actually processed ? Heres my 3 assumptions ( lol )

    ( 1 )
    I've always thought they get clamped into a sliding jig and theres a spinning Circular disc the size of a record ( 12 inch dia ) with a very sharp outer edge. Its at a slight angle of say less than 5.
    Its touched to the edge of the board, and then the board is slid under the spinning disc.
    That slices all of the components off at board level.

    They get dropped onto a conveyor which spits the nonmagnetic pieces out over its end, into mid air, and air seperations used to blast them off in diferent directions into drums for metal recovery.

    While magnetic ones get stuck to the magnetic roller & pass over & under the end of the conveyor, past the magnetic roller until they fall into their own drum.

    OR ( 2 }

    They get put into a large mesh container & dumped into a vat of hot Hydrochloric acid where the solders dissolved & the components fall into a recovery pan.
    Components are then removed, washed, dried, sorted & processed.
    The board itself is mulched into pulp & the Copper is dissolved out & recovered ( along with Gold, Brass, Tin & Copper ) They do this to the boards above too.

    OR. { 3 )

    Its a Copper mine setup.
    The mined Copper granules are put into a melting pot & melted. Then the boards are chucked into the molten Copper, everything melts but the Steel which is removed somehow. The boards act as a flux or to cover the molten metal & are skimmed off before pouring.
    The Copper mix is poured out as bars or such. Then rolled or granulated or something.
    Then its put into a electroplating bath & the Coppers dissolved & plated onto sheet electrodes while thecother metals end up in the sludge & are recovered thru many, mostly electroplating, processes.

    Since all of this is done to mined Copper anyway, adding the boards simply raises the 'other metals' content & thats how they get the escrap $$ back.

    In this case, the condition of the boards won't matter much, ripped, broken or damaged would still be ok & the quality could vary from above 'Power supply' to ' High grade telecom',
    The prices paid for the scrap would be lower because theres less work needed for sorting boards out by the sellers & the process is more basic, it would take longer to do & the extra transport costs to remote Copper mines & refinerys.

    While in process 1 & 2.
    In 1,. Any boards would be processed dry & even power supplys because Aluminium capactors & Ferrite coils, chokes & transformers get seperated out immediately & every type of component gets its own bin for bulk taylored processing.

    While in ( 2 ) each sort of board would be saved up & processed in bulk, even indicidual board sorts would be regraded before processing.
    Say, Memory sticks would be graded into size of the board, & year of manufacture & memory capacity.
    The actual recovery of Gold & such would be already known before the process is started. That way when they do the next processes they know how much they will get & when to stop processing. ( Electroplating metals out )

    Hard drive boards have the best recovery from what I have read, certain years of manufacture used the yellow block Tanti capactors. Thats just one way they would seperate the boards.
    But i think they would seperate them into individual models of boards.

    I figured if its process ( 1 ), the skimming of the components off the boards with a knife, that the boards could not be damaged in almost any way.

    So.. TLDR ?
    How are the escrap Hard Drive boards processed anyway? Exactly how? Thanks/ e

  7. The Following 3 Users say Thank You for This Post by eesakiwi:


  8. #5
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Maple Ridge, BC, Canada
    Posts
    225
    Thanks
    82
    Thanked 267 Times in 109 Posts
    Quote Originally Posted by eesakiwi View Post
    How is the board actually processed ? Heres my 3 assumptions ( lol )
    Usually, none of the above.

    Boards are shredded, sometimes blended with other materials, to get the copper content higher.
    The shredded boards are smelted and copper cathodes are poured. The copper acts as a collector of all the precious metals. Iron, aluminum, etc go in the slag.
    The copper cathodes are placed in an electrolytic cell, and current is applied. The copper will dissolve and get deposited on the cathode as pure copper (99.99% or so).
    All the precious metals and other impurities fall to the bottom of the tank, called anode slimes.
    The anode slimes are further processed to separate the various precious metals and purify them.

    This would be basically the same process for all ewaste on a large scale. Companies like Umicore, Boliden, Metalor, etc use some variation of this process.
    Depopulating boards and separating components is usually only done by small scale or home refiners.

  9. The Following 2 Users say Thank You for This Post by aurum:



  10. Similar threads on the Scrap Metal Forum

    1. Connecticut - Buying hard drive magnets & hard drives
      By CTscrapman in forum Scrap Buyers & Sellers
      Replies: 106
      Last Post: 04-07-2018, 04:00 PM
    2. Hard Drive Arm
      By bpatnoe in forum Computer Recycling
      Replies: 29
      Last Post: 09-27-2013, 07:00 AM
    3. Hard Drive Erase Software. Requirements For Selling Hard Drives
      By Jeremiah in forum General Electronics Recycling
      Replies: 37
      Last Post: 08-23-2013, 03:30 AM
    4. Values For Different Hard Drive Board
      By Jeremiah in forum General Electronics Recycling
      Replies: 1
      Last Post: 12-18-2012, 06:13 PM
    5. How to kill hard drives fast and simple
      By easyrecycle in forum General Electronics Recycling
      Replies: 23
      Last Post: 01-19-2012, 08:25 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook