Results 1 to 9 of 9

Tower Fans- Love 'em or Hate 'em?

| Scrap Metal Tips and Advice
  1. #1
    recyclersteve started this thread.
    SMF Badges of Honor


    Member since
    Apr 2018
    Location
    United States
    Posts
    268
    Thanks
    212
    Thanked 179 Times in 97 Posts

    Tower Fans- Love 'em or Hate 'em?

    I don't know how you guys feel about tower fans. First, because there is so much sloppy terminology just about everywhere, let me clarify what I mean by tower fans. Specifically, I am referring to those floor standing fans that are about 3-3 1/2 feet tall and perhaps 6" to 9" wide. They are typically round and often have a feature that allows them to oscillate so that multiple people sitting in different areas of the same room can be comfortable.

    Now, that out of the way, let me give you my experience on tower fans. I don't know how many in total I saw before I decided to start picking them up, but I've actually picked up four of them this summer. Two worked fine, but I needed to clean out the insides (lots of dust) before allowing them to be used by my family.

    The other two that didn't work- that was a different story. I took them apart and both were quite a bit of work without much in results. In both cases the motors had screws that I stripped accidentally so that I couldn't really take apart the motors. Also, the motors and brackets seem to be quite oily and messy to work with.

    I kept some notes on the second fan. It was a Lasko brand and quite tall- taller than the usual tower fans. Unlike the first fan I took apart, the Lasko one didn't have those triangles with a number from 1 thru 7 to indicate that the plastic could be recycled. Too bad. The first one DID have plastic that was recyclable.

    I counted the screws that I removed to take this baby apart. I removed a whopping 74 screws on the Lasko fan and there were at least 8 more that I didn't remove because I didn't need to in order to remove the scrap. All the screws required a Phillips head screwdriver, but there were probably 5 or 6 different sizes. Way too much for for less than 3 1/2 ounces of soft copper wire (not including the power cord, since I could just clip it without having to open the fan), a motor that I couldn't take apart, and a few metal parts.

    Even though 2 of these taken apart is not a big sample size, the early returns are not promising for tower fans. They take up a fair amount of space (in my car and in my back yard). I didn't mind the waste of time as there is quite a learning curve to scrapping and I don't mind chalking it up as a learning experience.



    For the amount of effort, space taken and tiny returns, I am leaning toward just snipping the power cords in the future and moving on. The only problem with that strategy is that if the fan works, I can use it for my house. So that means I need to take it home first, even if I only get a power cord out of it.

    What does everyone else think about tower fans?

  2. The Following User Says Thank You to recyclersteve for This Post:



  3. #2
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    If they don't work (they sell good at yard sales) I cut the cord and put the rest in with the shred as is.
    Better than the dump!

  4. The Following User Says Thank You to hobo finds for This Post:


  5. #3
    t00nces2's Avatar
    SMF Badges of Honor


    Member since
    Jul 2014
    Location
    Sarasota, FL
    Posts
    1,693
    Thanks
    1,187
    Thanked 2,341 Times in 958 Posts
    I break them down to the motor and sell them as Lt Motors for a few cents more than shred.

  6. #4
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,873
    Thanks
    1,638
    Thanked 1,733 Times in 893 Posts
    Alot of them are filled with dog / cat hair. I will still take them depending on what else i already have waiting to be broken down, some times i just dont want to deal with all that plastic

  7. The Following 2 Users say Thank You for This Post by greytruck:


  8. #5
    SMF Badges of Honor


    Member since
    Jun 2017
    Location
    Las Vegas
    Posts
    1,306
    Thanks
    3,232
    Thanked 1,922 Times in 785 Posts
    What hobo finds said

  9. #6
    jimicrk's Avatar
    SMF Badges of Honor


    Member since
    Sep 2013
    Location
    Tennessee
    Posts
    2,825
    Thanks
    2,917
    Thanked 4,838 Times in 1,877 Posts
    I get maybe 1 or 2 electric motors a year and they usually end up in the shred pile. One of the first motors I tried to break down cost me a trip to the doctors, 4 or 5 stitches and a bill for 175 dollars. I think I'll stick with computers and phone systems.
    Last edited by jimicrk; 10-05-2018 at 04:17 PM.

  10. The Following 4 Users say Thank You for This Post by jimicrk:


  11. #7
    kirstenblain's Avatar
    SMF Badges of Honor

    Member since
    May 2020
    Location
    Texas
    Posts
    20
    Thanks
    3
    Thanked 2 Times in 1 Post
    I’ve taken a few of these apart for the copper inside the motor. I’m filling a 5 gal bucket to melt.

    I do make sure it’s pure copper, and not CCA.

  12. #8
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    I wouldn't ingot any recyclable metal. Its just wasted time & equipment co$t$ & the scrap buyer cannot know whats inside it so you will always get the lowest $ value for it.
    Thats if they would buy it.

    Melting Aluminium into items that sell would be a good way of making extra $$ from scrap.
    But then its really a Casting operation, not scrapmetal.

  13. #9
    hills's Avatar
    SMF Badges of Honor



    Member since
    Sep 2017
    Location
    Maine
    Posts
    1,351
    Thanks
    797
    Thanked 1,276 Times in 721 Posts
    I'm okay with tower fans. They're not terribly hard to do and net about 1/3 lb of #2 copper.

    In general: Scrapping is mostly about chasing pennies, nickels, dimes, and quarters. It doesn't make money sense to melt on a small scale.

  14. The Following User Says Thank You to hills for This Post:

    APA


  15. Similar threads on the Scrap Metal Forum

    1. My love hate relationship with eBay
      By alloy2 in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 7
      Last Post: 06-01-2016, 06:11 PM
    2. old printer, ugh, gotta hate em and, love em.
      By EcoSafe in forum A Day in the Life of a Scrapper
      Replies: 16
      Last Post: 05-20-2012, 09:08 PM
    3. PC fans
      By copycat in forum General Electronics Recycling
      Replies: 10
      Last Post: 04-27-2012, 06:55 PM
    4. love...hate relationship
      By scrappy888 in forum A Day in the Life of a Scrapper
      Replies: 8
      Last Post: 03-22-2012, 09:31 PM
    5. PC Fans
      By drozenski in forum General Electronics Recycling
      Replies: 7
      Last Post: 11-16-2011, 07:41 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook