Results 1 to 11 of 11

When I first started scrapping

| Scrap Metal Tips and Advice
  1. #1
    hobo finds started this thread.
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts

    When I first started scrapping

    When I first started scrapping I always said "steel Sucks!" and I would pass it up to get the good stuff. I would pass on BBQ Grills as the frame was steel and so many other things. Then when I was trying to sell aluminum the guy would bust my balls over a steel screw or rivet. This started me to break items down. I would bring in extruded alum frames and a bucket of the steel screws with it. This got the guy off my A$$. And he paid $.01 a pound for the steel. As I broke down more items BBQ Grills I know had a steel frame so I figured take it in with my steel screws.

    I no longer break down vacuums or carpet cleaners just cut the cord and add the rest to the shred. Even when steel was $.115 a pound I was still breaking down things to get the motors which were paying around $.30 and the wires were $1 a pound. Breaking down things is fun and I feel if you are starting out you should break down items to see what's inside them and then do the math if it is worth breaking down for extra cash or not. A Swiffer with the plastic on it weighs more than breaking it down so I had to figure out clean alum price vs. dirty alum.

    Shred steel is normally the lowest price you get from a yard, but going to the yard with shred taught me many things.



    Read the stuff here I have learned lots from this site. Made more money and some friends as well.

    And some scrap quotes...
    “People may laugh at me, but that's ok. I laugh all the way to the bank.” Mick
    “Anyone who thinks scrappin is easy money ain't doin it right!" Olddude
    "The first 50 years are for learning, the next 50 are for living." Patriot76
    Last edited by hobo finds; 06-22-2017 at 03:57 PM.

  2. The Following 16 Users say Thank You for This Post by hobo finds:



  3. #2
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,873
    Thanks
    1,638
    Thanked 1,733 Times in 893 Posts
    3 great quotes right there

  4. The Following User Says Thank You to greytruck for This Post:


  5. #3
    Sirscrapalot's Avatar
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    A sandbar off the atlantic..OBX,NC
    Posts
    6,123
    Thanks
    11,885
    Thanked 8,783 Times in 3,854 Posts
    ...no cooler or goat? seriously?


    I'm revoking your goat card and Cooler Puller Membership.


    Sirscrapalot - Yes I'm kidding, untwist the knickers.

  6. The Following 2 Users say Thank You for This Post by Sirscrapalot:


  7. #4
    SMF Badges of Honor

    Member since
    Dec 2012
    Location
    Virginia Beach, VA
    Posts
    345
    Thanks
    643
    Thanked 620 Times in 191 Posts
    How did Sirscrapalot not make the quote list?
    I'm going to recycle the world.

  8. The Following User Says Thank You to Tincankeith for This Post:


  9. #5
    Sirscrapalot's Avatar
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    A sandbar off the atlantic..OBX,NC
    Posts
    6,123
    Thanks
    11,885
    Thanked 8,783 Times in 3,854 Posts
    If I'm going to come in fourth, it's good company to be a runner up to.

    An they are excellent quotes.

    hobo is my buddy tho, I gotta bust his chops.

    Sirscrapalot - One love. - Bob Marley

  10. The Following 2 Users say Thank You for This Post by Sirscrapalot:


  11. #6
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,589
    Thanked 7,220 Times in 2,256 Posts
    Hobo Finds

    Thank you for your reference to my quote. I need to change it to the first 65 years is for learning as every day is another lesson. To be included in reference to Mick and Old Dude is an honor.


    d
    Give back more to this world than we take.

  12. The Following 4 Users say Thank You for This Post by Patriot76:


  13. #7
    mike1's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    Rochester indiana
    Posts
    550
    Thanks
    231
    Thanked 93 Times in 76 Posts
    yeah me i dont like steel i just call a guy to pick it up when im done getting the non ferrous out=) i try and not do tv's since he doesn't take the tubes they are to much for me. i to cut cords cause the motors are so small and hard to get to on sweepers/shop vacs after all the cord is where the copper is lol.

  14. #8
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    Quote Originally Posted by mike1 View Post
    yeah me i dont like steel i just call a guy to pick it up when im done getting the non ferrous out=) i try and not do tv's since he doesn't take the tubes they are to much for me. i to cut cords cause the motors are so small and hard to get to on sweepers/shop vacs after all the cord is where the copper is lol.
    Something you might want to think about is if you have room getting a decent used flatbed trailer with rails. You can put your steel on it until you have a full trailer load, then take it in to the yard. Just a few trips and that trailer is paid for. That is what I do, basically use my flatbed as a storage place for my steel after I have processed it, then take it in to the yard after the trailer is full. Realistically speaking I have made more from shred than all the other metals combined.

  15. The Following 5 Users say Thank You for This Post by wayne1956:


  16. #9
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    A lot of the time I do not worry about whether the "cash gain" is worth it or not. As much as anything else, processing scrap for me is therapeutic. If I have had a stressful day, often I will go to my processing pile and start to take stuff apart. It is relaxing for me.

  17. The Following 4 Users say Thank You for This Post by wayne1956:


  18. #10
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,589
    Thanked 7,220 Times in 2,256 Posts
    Quote Originally Posted by wayne1956 View Post
    Something you might want to think about is if you have room getting a decent used flatbed trailer with rails. You can put your steel on it until you have a full trailer load, then take it in to the yard. Just a few trips and that trailer is paid for. That is what I do, basically use my flatbed as a storage place for my steel after I have processed it, then take it in to the yard after the trailer is full. Realistically speaking I have made more from shred than all the other metals combined.
    This is excellent advice for every one that scraps. Why give away your profits? Benjamin Franklin is credited with a quote (unproven) "A Penny earned is a penny saved".

  19. The Following User Says Thank You to Patriot76 for This Post:


  20. #11
    mike1's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    Rochester indiana
    Posts
    550
    Thanks
    231
    Thanked 93 Times in 76 Posts
    Quote Originally Posted by Patriot76 View Post
    This is excellent advice for every one that scraps. Why give away your profits? Benjamin Franklin is credited with a quote (unproven) "A Penny earned is a penny saved".
    yes indeed good quote=)


  21. Similar threads on the Scrap Metal Forum

    1. If you had $5000. to get started in scrapping how would you use it?
      By metalworks55 in forum General - Let's talk business
      Replies: 84
      Last Post: 12-20-2014, 03:41 PM
    2. Hi to all, just started scrapping
      By js1 in forum Introduce yourself
      Replies: 6
      Last Post: 05-06-2013, 11:00 PM
    3. just started scrapping...first find
      By Troyer16 in forum A Day in the Life of a Scrapper
      Replies: 5
      Last Post: 07-15-2012, 11:10 AM
    4. Scrapping Basics - Getting Started
      By admin in forum Beginners Start Here - Metal Recycling Basics
      Replies: 2
      Last Post: 05-21-2012, 03:14 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook