Results 1 to 19 of 19

Stripping copper from a Washing Machine Motor?

| Scrap Metal Tips and Advice
  1. #1
    p3rs0n started this thread.
    SMF Badges of Honor

    Member since
    May 2013
    Posts
    5
    Thanks
    0
    Thanked 1 Time in 1 Post

    Stripping copper from a Washing Machine Motor?

    Hi, I'm not sure if this is the right place to ask this, but if not, can you please steer me in the right direction? What is the fastest and easiest way to strip copper off a washing machine motor please?

    I'd post a picture up but it won't let me yet.

    Basically, it is the type where there is copper wound around each individual rotor finger if that makes sense?

    The way I was doing it, I managed to give myself some nice infected cuts on my fingers from repetitively winding it off.

    Thanks.

  2. The Following User Says Thank You to p3rs0n for This Post:



  3. #2
    cummins's Avatar
    SMF Badges of Honor


    Member since
    Apr 2013
    Location
    ontario
    Posts
    573
    Thanks
    15
    Thanked 255 Times in 171 Posts
    watch a few you tube videos....all EM are pretty much the same. 90% of the windings in appliances we scrap are aluminum.

    i use a grinder and a punch them out with a punch/hamer or pry them out with a screw driver

  4. The Following User Says Thank You to cummins for This Post:


  5. #3
    jghilino's Avatar
    SMF Badges of Honor

    Buying Specialty Escrap of all kinds, resale grade computer parts

    Member since
    Sep 2012
    Location
    KANSAS CITY
    Posts
    2,672
    Thanks
    1,429
    Thanked 1,453 Times in 919 Posts
    i usually strip the stators and leave the rotors as-is

    i use a 6" angle grinder with cutoff wheel, cut the copper off one end then use a hammer and punch to drive the rest out the other side

    this video shows the same technique

    I buy and sell all types of scrap and escrap. I buy specialty and hard to sell escrap. I buy resale items. PM me or contact me at jghilino@hotmail.com
    I AM ACTIVELY BUYING ESCRAP OF ALL TYPES. BOARDS, RAM, CPUS AND MUCH MORE

  6. The Following User Says Thank You to jghilino for This Post:


  7. #4
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    I found a rotor from an oscillating fan(with the longer shaft) works perfect for driving it through there

  8. The Following User Says Thank You to Bear for This Post:


  9. #5
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  10. The Following 2 Users say Thank You for This Post by Mechanic688:


  11. #6
    jghilino's Avatar
    SMF Badges of Honor

    Buying Specialty Escrap of all kinds, resale grade computer parts

    Member since
    Sep 2012
    Location
    KANSAS CITY
    Posts
    2,672
    Thanks
    1,429
    Thanked 1,453 Times in 919 Posts
    thats the video i was looking for, just couldnt find it

  12. #7
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    Quote Originally Posted by jghilino View Post
    thats the video i was looking for, just couldnt find it
    It was right down below in that other recommended thread by geravega77.
    I'm not that good, can't read your mind yet,,,

  13. #8
    p3rs0n started this thread.
    SMF Badges of Honor

    Member since
    May 2013
    Posts
    5
    Thanks
    0
    Thanked 1 Time in 1 Post
    Thanks for the info.. but I don't mean that type of washing machine rotor.. I mean one that looks like this please..
    If you type in "washing machine wind turbine" into google images.. I'm trying to strip copper off the ones that look like that in the second image. Can someone who is allowed to post up links and pictures place a link to that image please? :P

    Thanks again.

  14. #9
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    my post it links aren't showing http://hackedgadgets.com/wp-content/...e-wiring_2.JPG
    I'd remove the blue part and put the rest in whole elec motors

    Last edited by Mechanic688; 05-28-2013 at 12:17 AM. Reason: added pic

  15. #10
    p3rs0n started this thread.
    SMF Badges of Honor

    Member since
    May 2013
    Posts
    5
    Thanks
    0
    Thanked 1 Time in 1 Post
    Quote Originally Posted by Bear View Post
    my post it links aren't showing http://hackedgadgets.com/wp-content/...e-wiring_2.JPG
    I'd remove the blue part and put the rest in whole elec motors


    And if I wanted to strip it.. what is the best way please?

  16. #11
    p3rs0n started this thread.
    SMF Badges of Honor

    Member since
    May 2013
    Posts
    5
    Thanks
    0
    Thanked 1 Time in 1 Post
    Anyone please? :P

  17. #12
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    There is no best way. I just throw those with copper-bearing.
    People may laugh at me, but that's ok. I laugh all the way to the bank.

  18. #13
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    ok, here's what you'll get out of it http://hackedgadgets.com/wp-content/..._re-wiring.jpg and the best way i could see would likely be to use a small angle grinder with a cutting wheel and cut through the top of each winding, then remove the copper from the other side

  19. #14
    jghilino's Avatar
    SMF Badges of Honor

    Buying Specialty Escrap of all kinds, resale grade computer parts

    Member since
    Sep 2012
    Location
    KANSAS CITY
    Posts
    2,672
    Thanks
    1,429
    Thanked 1,453 Times in 919 Posts
    take a razor knife or a dremel with cut off wheel, and cut across the windings length wise, at that point the copper should come out easily

  20. #15
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    What a time waster.

  21. #16
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    Quote Originally Posted by Mechanic688 View Post
    What a time waster.
    Yeah, they take me 20 mins to unwind by hand...

    I unwind the 3 wires at the same time & the wire keeps getting caught at the ends of each winding, so some unwind at that point & some don't. Then I have to unwind by hand individually the caught wires, then off to unwinding 3 wires at a time again.

    I have cut thru the sides of the windings with a grinder, but the plastic gets warm & soft & catches the wire when it gets cold, you end up pulling some plastic off at the same time & the wire looks bad with it on it.

    I tried burning the plastic off to get to the wire, but thats not a time saver either.

    I tried cutting thru the windings with a cold chisle, takes a lot of time & it gets messy with the loose loops flying off everywhere.

    No real simple way to do it, except for unwinding them by hand.

    The motors with a dark purple wire on them are made of Ali wire too. Only the motors with the thickest wire is any good for generating power from the units.

  22. The Following User Says Thank You to eesakiwi for This Post:


  23. #17
    Gravitar's Avatar
    SMF Badges of Honor



    Member since
    Jul 2012
    Location
    Central Texas
    Posts
    1,086
    Thanks
    1,258
    Thanked 1,431 Times in 525 Posts
    Or a Skil Saw with and angle grinder wheel, I think that's what he's using.
    Made in China, Recycled in the Republic of Texas!

    "When the mind fails, brute force prevails" - CTSSolutions

  24. #18
    jghilino's Avatar
    SMF Badges of Honor

    Buying Specialty Escrap of all kinds, resale grade computer parts

    Member since
    Sep 2012
    Location
    KANSAS CITY
    Posts
    2,672
    Thanks
    1,429
    Thanked 1,453 Times in 919 Posts
    Watching him throw sparks at a $30,000 classic car to recover $4 worth of copper, priceless

  25. #19
    p3rs0n started this thread.
    SMF Badges of Honor

    Member since
    May 2013
    Posts
    5
    Thanks
    0
    Thanked 1 Time in 1 Post
    It takes me a few hours to do it by unwinding it haha. And I end up getting cuts on my index and middle finger from doing so. Last time I managed to get that cut infected from either dirty stuff that was on the copper from the washing machine or from the spark plugs I was playing with a week later as the cut wasn't heeling.



    So yeah, trying to find a quicker and better way!


  26. Similar threads on the Scrap Metal Forum

    1. Removing copper from a washing machine motor
      By geravega77 in forum Scrap Metal Videos
      Replies: 25
      Last Post: 09-23-2019, 05:35 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook