Results 1 to 16 of 16

using a screwdriver as a chisel

| Scrap Metal Safety and Hazards
  1. #1
    NHscrapman started this thread.
    NHscrapman's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    new hampshire
    Posts
    1,582
    Thanks
    4,076
    Thanked 2,168 Times in 940 Posts

    using a screwdriver as a chisel

    Hammering open electric motors yesterday using a screwdriver instead of going to get my chisels and had the plastic handle of the screwdriver explode sending shrapnel into my hand. Nothing serious but it definitely can be avoided by using the right tool or wrapping the handle of the screwdriver in electric/ duct tape. Luckily it was a craftsman so i got a new screwdriver. now if craftsman only sold hands....

    There ain't nothing wrong with an honest days work. Anyone who says otherwise is a fool.- Old Man

  2. The Following 2 Users say Thank You for This Post by NHscrapman:



  3. #2
    waredu's Avatar
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Texas
    Posts
    309
    Thanks
    95
    Thanked 260 Times in 125 Posts
    I have several extra holes in various body parts from using screwdrivers as chisels/prybars/punches etc. You'd think I'd learn - but they're always around and work "almost" as I intend them to.

  4. The Following 3 Users say Thank You for This Post by waredu:


  5. #3
    NHscrapman started this thread.
    NHscrapman's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    new hampshire
    Posts
    1,582
    Thanks
    4,076
    Thanked 2,168 Times in 940 Posts
    Quote Originally Posted by waredu View Post
    I have several extra holes in various body parts from using screwdrivers as chisels/prybars/punches etc. You'd think I'd learn - but they're always around and work "almost" as I intend them to.
    Yeah they are too handy sometimes
    Pun intended

  6. #4
    SMF Badges of Honor

    Member since
    Oct 2012
    Location
    Alabama
    Posts
    760
    Thanks
    1,066
    Thanked 1,209 Times in 468 Posts
    Ouch, I usually have a chisel for that kind of work, but screwdriver as prybar is a habit I need to break before it bites me.

  7. #5
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,407
    Thanks
    363
    Thanked 3,083 Times in 1,326 Posts
    I sharpen a small screwdriver on a whetstone and use it as a chisel to break IC chips loose from RAM. Maybe not the right tool but works great. I think the screwdriver is easier to grasp and readily takes a sharper angle. I'm not hitting it hard - mainly using it to "cut" the solder on 1 or 2 sides (half of the soldered sides), then twist the chip.
    People may laugh at me, but that's ok. I laugh all the way to the bank.

  8. The Following 2 Users say Thank You for This Post by Mick:


  9. #6
    NHscrapman started this thread.
    NHscrapman's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    new hampshire
    Posts
    1,582
    Thanks
    4,076
    Thanked 2,168 Times in 940 Posts
    Excessive force was the main factor in the explosion i'm sure. The wonders of kinetic energy

  10. #7
    redcrossnj's Avatar
    SMF Badges of Honor


    Member since
    Oct 2011
    Location
    central jersey
    Posts
    465
    Thanks
    28
    Thanked 242 Times in 143 Posts
    I use Harbor freight screwdrivers as punches. I cut the tips off them. The only handle that's ever exploded on me was the handle of a screwdriver from home depot

  11. #8
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,521
    Thanks
    2,836
    Thanked 2,537 Times in 1,217 Posts
    Its not a screwdriver, its a screwturner..........

    Yeah, its a bad habit to get into, sorta like stripping wire with your teeth... Untill it bites you back.

    I remember those little blue rectangles in my left hand from a slipping screwdriver too.

    But, the same effect the op got from the plastic handle is magnefied a thousand times if you do not grind off the gradually widening head from a cold chisle.
    Neighbour got bitten, found part of it embedded under his fingernail.

  12. The Following User Says Thank You to eesakiwi for This Post:


  13. #9
    sawmilleng's Avatar
    SMF Badges of Honor


    Member since
    Feb 2013
    Location
    Central Kootenays, BC, Canada
    Posts
    861
    Thanks
    713
    Thanked 1,195 Times in 520 Posts
    There are screwdrivers available with the shank running right through the handle...so you can beat on the top of the handle and be hitting the steel screwdriver shank. One brand I use that is made that way is "Jet", but I'm sure there's lots out there if you look around for them. I have heard them called "mechanics screwdrivers". Maybe they should be called "scrapper's screwturners--SST's".

    Jon.

  14. The Following User Says Thank You to sawmilleng for This Post:


  15. #10
    SMF Badges of Honor

    Member since
    Oct 2013
    Location
    Indianapolis
    Posts
    16
    Thanks
    0
    Thanked 9 Times in 5 Posts
    Thanks for sharing ... I know I have taken lots of short cuts... so thanks for the reminder...
    J

  16. #11
    Sirscrapalot's Avatar
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    A sandbar off the atlantic..OBX,NC
    Posts
    6,118
    Thanks
    11,853
    Thanked 8,755 Times in 3,848 Posts
    Ha! I do better with a chisel as a screwdriver then I do using a chisel for it's normal uses!

    My scars can testify..

    Sirscrapalot - There is something beautiful about all scars of whatever nature. A scar means the hurt is over, the wound is closed and healed, done with. ~ Harry Crews

  17. #12
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,711
    Thanks
    6,798
    Thanked 3,450 Times in 1,984 Posts
    They're simply designed different due to having different uses. Screwdrivers are designed to turn, and chisels for blunt impact. Better chisels usually have a full length shaft with a full strike on the end, and the handles are usually considerably larger than screwdriver handles, no doubt to give most people a better chance of hitting the strike instead of their hand ; ) The strike isn't hardened as much as the point so not to throw sparks when hit with a hammer, but glasses are still mandatory if you appreciate your eyesight. Cold chisels are tempered the same way (hardened point, softer strike) and are intended to be used with both glasses and gloves

  18. The Following 2 Users say Thank You for This Post by Bear:


  19. #13
    Jillyenator's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Asheville, NC. Also Arizona.
    Posts
    346
    Thanks
    853
    Thanked 277 Times in 141 Posts
    Wrapping the plastic handles with tape is an excellent idea, and thank you.

  20. The Following User Says Thank You to Jillyenator for This Post:


  21. #14
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Wisconsin
    Posts
    26
    Thanks
    42
    Thanked 13 Times in 11 Posts
    Quote Originally Posted by Bear View Post
    They're simply designed different due to having different uses. Screwdrivers are designed to turn, and chisels for blunt impact. Better chisels usually have a full length shaft with a full strike on the end, and the handles are usually considerably larger than screwdriver handles, no doubt to give most people a better chance of hitting the strike instead of their hand ; ) The strike isn't hardened as much as the point so not to throw sparks when hit with a hammer, but glasses are still mandatory if you appreciate your eyesight. Cold chisels are tempered the same way (hardened point, softer strike) and are intended to be used with both glasses and gloves
    They're also usually made of an impact resistant resin or hardwood with steel banding on the top and bottom to keep it from cracking/splintering.
    Like these old Stanleys
    http://i.ebayimg.com/00/s/MTIwMFgxNj...S1a0z/$_12.JPG

    If you're going to go the screwdriver route, usually the ones with the rubberized/not-plastic composite handle are better for banging on. Just don't whack too hard, an off-center strike will bounce the hammer. The material also tends to not mush out (?). They will cost you a few dollars up front, but I have a 12" flathead that I've used as a prybar, beater bar, awl, etc. and that sonofa***** is still kickin.

    And definitely stay away from any that seem very light and/or have visible seams down the handle.

  22. The Following 2 Users say Thank You for This Post by WorkDrinkSleepRepeat:


  23. #15
    Jillyenator's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Asheville, NC. Also Arizona.
    Posts
    346
    Thanks
    853
    Thanked 277 Times in 141 Posts
    I went to Harbor Freight and got my hands on a set of chisels (four for $6 - i think that is the current sale price). Walmart has a set of three for $6, btw (regular price). Lowes is the most expensive option; their sets are around $12.

    I am amazed at how much easier it is to get the ICs off. Pop!

    You got the tools, you got the talent...

  24. The Following User Says Thank You to Jillyenator for This Post:


  25. #16
    NHscrapman started this thread.
    NHscrapman's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    new hampshire
    Posts
    1,582
    Thanks
    4,076
    Thanked 2,168 Times in 940 Posts
    yes i now own chisels for metalworking (house set). bite me once... that's it, make it count.
    I took Micks advice and made the broken screw"turner" into an IC and component remover it works well and the price was right up my alley
    Last edited by NHscrapman; 02-27-2014 at 06:16 PM.


  26. Similar threads on the Scrap Metal Forum

    1. Looking For A New Cordless Screwdriver?
      By Mechanic688 in forum Tools and Equipment
      Replies: 14
      Last Post: 07-20-2014, 12:15 PM
    2. Which Cordless Screwdriver would you recommend?
      By mikedmissouri in forum General Electronics Recycling
      Replies: 37
      Last Post: 06-18-2013, 12:03 PM
    3. Screwdriver Bits
      By dmm2442 in forum Tools and Equipment
      Replies: 12
      Last Post: 04-24-2012, 03:31 PM
    4. Omigoshomigoshomigosh! Uncle gave me an air chisel!
      By newattitude in forum Tools and Equipment
      Replies: 12
      Last Post: 08-10-2011, 05:33 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook