Results 1 to 14 of 14

Are there Aluminum power cords?

| Scrap Metal Questions and Answers
  1. #1
    Troybud started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Posts
    14
    Thanks
    0
    Thanked 1 Time in 1 Post

    Are there Aluminum power cords?

    I found a power cord today and it looks like Aluminum but i wasnt sure if its just colored Copper that just looks like Aluminum.
    So are some power cords that are Aluminum?
    Thanks



  2. #2
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    I'm guessing its a 'soft' extension cord, with plenty of strands.

    Probably 'tinned copper' wire, cut some at a sharp angle & have a look at the cross section, it has probably got a copper/gold look to it.

    Could be stainless steel, I have found some in a oven once (or twice...) same test as above.

    Ali strands would melt over a hot flame

  3. #3
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    Milwaukee Wisc.
    Posts
    71
    Thanks
    35
    Thanked 44 Times in 22 Posts
    Hello Gentlemen,
    Interestingly enough, there is in fact such a thing as Aluminum power cords -and- Romax type wire, the Alumex Corporation produced it. I know this only because I have some in my wire collection / Wall display. "It's a scrappers nightmare" or a let down at best. But on that same note, it very well could be just simply tinned copper as eesakiwi mentioned.

  4. The Following User Says Thank You to GreenTruckR for This Post:


  5. #4
    GeorgeB's Avatar
    SMF Badges of Honor

    Member since
    Sep 2011
    Location
    Manassas Park, VA
    Posts
    2,919
    Thanks
    462
    Thanked 639 Times in 432 Posts
    I personally have never heard of aluminum being in any type of power cords or wire.

    You have the rubber coating, and then a smaller rubber coating, then copper, or you have this:

    Rubber coating, thin piece of steel, rubber coating, and then copper.

    The ones with steel, no yard I have been too will take it, but depending on quantity I will either strip it, or just throw it away with steel.
    George Beale - Founder & President - info@viprecyclingjunkremoval.com
    VIP Recycling Junk Removal LLC - Premier Scrap Metal, Junk, & Electronic Recyclers!
    http://www.viprecyclingjunkremoval.com

  6. #5
    KzScrapper's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    Denver Metro, CO
    Posts
    4,841
    Thanks
    7,019
    Thanked 5,792 Times in 2,417 Posts
    Quote Originally Posted by GeorgeB View Post
    I personally have never heard of aluminum being in any type of power cords or wire.

    You have the rubber coating, and then a smaller rubber coating, then copper, or you have this:

    Rubber coating, thin piece of steel, rubber coating, and then copper.

    The ones with steel, no yard I have been too will take it, but depending on quantity I will either strip it, or just throw it away with steel.
    There are many, many houses out there wired with aluminum Romax and it is a huge fire risk so they quit using it in the late 70's ish.
    Recyclable Material Merchant Wholesaler
    Certified Zip-Tie Mechanic
    "Give them enough so they can do something with it, but not too much that they won't do nothing."

  7. #6
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    tucson az
    Posts
    35
    Thanks
    7
    Thanked 5 Times in 5 Posts
    here in arizona we run across a lot of it it is indeed aluminum very common with older wires used in home and commercial buildings

  8. #7
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    Milwaukee Wisc.
    Posts
    71
    Thanks
    35
    Thanked 44 Times in 22 Posts
    Good Morning / AfterNoon to Everyone!

    Aluminum Wire: Thankfully for us scrappers it's not as common as CU is. But alum wire is out there in almost every guage you could imagine. At this Recovery site that I am at this very moment, we collected approx 200 some odd pounds of alum wire, solid 100% alum. strand as well as solid core, and yes there is also braided alum. tri-plex (Over-Head, High Tention wire) with the single steel wire running through the middle, surrounded by clean alum. Quite often it is refered to as Service Drop within the electrical industry.
    A couple years back I made a wall display showing the many different type of wires so our guys "and me" would have a better understanding how to seperate CU wire. Currently I am way out of town on a large Recovery site, however once we go back home I will take some good photo's of the display and post it on here.

    We still have about another week before we finish up here, so perhaps if I have time in the next day or two I will take a few pics of the alum wire that we still have here on site and post them. Hopefully it will help my fellow scrappers out in wire knowledge & identification.

    Last year I learned a hard lesson regarding alum wire. I had placed a bid on GSA.gov for (The Lot) consisting of 4- pallets of misc. wire, from the the auction pics I could clearly see that a lot of the wire on the pallets were Romex and romex type wire. We won the bid and two days later my brother and I arrived with the excitement of a little kid... approx. 1/2 of the wire was alum wire. Since then we are much more cautious when we bid online with GSA or IDOT.

  9. The Following User Says Thank You to GreenTruckR for This Post:


  10. #8
    skylinejack's Avatar
    SMF Badges of Honor


    Member since
    Jul 2011
    Location
    Baton Rouge, La.
    Posts
    827
    Thanks
    1,194
    Thanked 959 Times in 400 Posts
    Absolutely aluminum wire is out there. In abundance. On a power cord? Interesting. I've never seen it, but it's possible I guess. Do the heat test like eesakiwi suggest. If it's tinned copper (which would be my guess at this point) the yards here take it as #2 copper. Good luck with it.
    AMERICAN BORN, AMERICAN BRED! AND I'M PROUD TO BE AN AMERICAN!!!

  11. #9
    Troybud started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Posts
    14
    Thanks
    0
    Thanked 1 Time in 1 Post
    Ok thanks everybody

  12. #10
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    Milwaukee Wisc.
    Posts
    71
    Thanks
    35
    Thanked 44 Times in 22 Posts
    Hello to everybody once again !
    A couple days ago there was this discussion regarding aluminum wire. There were a few people who didn't realize that in fact there is aluminum wire out there. I stated that I would take a photo of some aluminum wire that we just recovered on a salvage yard site that we are currently on.

    I don’t want to be redundant, however I always keep my word and do what I say I'm going to do. That being said, here is the photo I took on Sunday.

    Truly,
    Scott

    Aluminum wire: http://i1209.photobucket.com/albums/...lumwire005.jpg
    GT Recycling & Reclaiming

    Quote Originally Posted by GeorgeB View Post
    I personally have never heard of aluminum being in any type of power cords or wire.

    You have the rubber coating, and then a smaller rubber coating, then copper, or you have this:

    Rubber coating, thin piece of steel, rubber coating, and then copper.

    The ones with steel, no yard I have been too will take it, but depending on quantity I will either strip it, or just throw it away with steel.
    Last edited by GreenTruckR; 11-29-2011 at 10:23 PM. Reason: Just learning how to post photo'S

  13. The Following 2 Users say Thank You for This Post by GreenTruckR:


  14. #11
    ParkerFlyer4's Avatar
    SMF Badges of Honor

    Member since
    Nov 2011
    Location
    north west
    Posts
    407
    Thanks
    423
    Thanked 524 Times in 188 Posts
    Quote Originally Posted by GreenTruckR View Post
    I have some in my wire collection / Wall display. "It's a scrappers nightmare" or a let down at best.
    some pics of your collection would be helpful / interesting / appreciated.

  15. #12
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    I'm finding more & more Aluminum wire in the microwave transformers.
    Out of the last three that I scrapped, two of them had 1 of the 2 coils in the transformer made from Ali.

    Any silver/stainless steel microwave I'd suspect has at least 1 coil made from Ali, maybe both made of Ali.
    Yah have to check them by scrapeing them. Silver = Ali wire, they always have a gold/copper coloured varnish painted on them too.

  16. #13
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    The white wire in the pic above is pretty self explanatory as it is marked Aluminex.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  17. #14
    Filthy's Avatar
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Northern New Jersey
    Posts
    780
    Thanks
    850
    Thanked 372 Times in 202 Posts
    Aluminex. ouch
    We're the renegades of Junk!


  18. Similar threads on the Scrap Metal Forum

    1. power supply cords
      By metaljacket in forum General Electronics Recycling
      Replies: 4
      Last Post: 07-01-2019, 06:27 PM
    2. Check ebay before scrapping old appliance power cords
      By bjybjy in forum More than Scrap Value
      Replies: 5
      Last Post: 08-05-2015, 06:34 PM
    3. Standard 6-foot Power Cable or Power Cord
      By Recyclotrops in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 9
      Last Post: 08-09-2012, 09:03 PM
    4. Extension Cords
      By TexasDeere in forum Scrap Metal Questions and Answers
      Replies: 8
      Last Post: 08-02-2012, 10:05 PM
    5. Power cords for dryers
      By wayne1956 in forum Scrap Metal Questions and Answers
      Replies: 8
      Last Post: 04-24-2011, 10:22 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook