Results 1 to 10 of 10

Anodised aluminium

| Scrap Metal Questions and Answers
  1. #1
    Sean2638 started this thread.
    SMF Badges of Honor

    Member since
    Jul 2020
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Anodised aluminium

    Looking for some advice.



    Im building my own foundry and I have a load of old aluminium heat sinks laying about that I thought I could melt down instead of trashing.

    Does the fact that the aluminium is anodised cause any problems?

    Thanks


  2. #2
    scrapman1077's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    Alabama
    Posts
    76
    Thanks
    5
    Thanked 79 Times in 32 Posts
    No, anodize is a very thin layer of aluminum oxide, it will float to the top.

  3. #3
    Sean2638 started this thread.
    SMF Badges of Honor

    Member since
    Jul 2020
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Great thanks.

    Would the anodised layer stay in one piece that I could easily pick out of the molten aluminium?

  4. #4
    WhiteSquirrel's Avatar
    SMF Badges of Honor

    Member since
    May 2020
    Location
    Ontario, Canada
    Posts
    101
    Thanks
    17
    Thanked 123 Times in 61 Posts
    Just need a skimmer and it'll be easy to skim out with a layer of slag. I keep all the slag and do a quick remelt every now and then to recover as much Al as possible.

    Once it's cold, that layer is easy to break off of the remelt slag by hand, and you can toss that dross then.

  5. #5
    Sean2638 started this thread.
    SMF Badges of Honor

    Member since
    Jul 2020
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Ok great.

    I’ve only seen small foundries.


    I want to build an electric one 50cm x 50cm x 50cm

    If I use enough insulation do you think it’s still possible to have one this size?

  6. #6
    WhiteSquirrel's Avatar
    SMF Badges of Honor

    Member since
    May 2020
    Location
    Ontario, Canada
    Posts
    101
    Thanks
    17
    Thanked 123 Times in 61 Posts
    Quote Originally Posted by Sean2638 View Post
    Ok great.

    I’ve only seen small foundries.


    I want to build an electric one 50cm x 50cm x 50cm

    If I use enough insulation do you think it’s still possible to have one this size?
    Heck. YES!

    Outer layer is 19 inches across, with my large burner this thing melts alum faster than I can keep up with feeding the crucible. Word of caution though : the extra fire pot and air causes some increased scaling rate using steel crucibles, so I would suggest getting a large graphite one.
    Last edited by WhiteSquirrel; 07-07-2020 at 11:25 AM.

  7. #7
    Sean2638 started this thread.
    SMF Badges of Honor

    Member since
    Jul 2020
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    If I was building it with electric rather than a burner how much insulation do you reckon I’d need?

    I was looking at graphite anyway. Didn’t think steel would be much use if I do manage to make an amazing foundry as the steel might melt haha
    Last edited by Sean2638; 07-07-2020 at 12:19 PM.

  8. #8
    WhiteSquirrel's Avatar
    SMF Badges of Honor

    Member since
    May 2020
    Location
    Ontario, Canada
    Posts
    101
    Thanks
    17
    Thanked 123 Times in 61 Posts
    I always use 2 inch refractory wool since it keeps its shape nice, but 1 inch would be good enough. Slap a layer or two of sealant/coating on that, and you should be good to melt anything up to 1200C.

    There are some awesome electric furnace videos out there, with VOG on youtube having one of the neatest setups I've seen. I recommend playing around around with whatever you have laying around until you have something that works the way you want it, then spent the time and money to make that setup into something a little more permanent.

  9. #9
    Sean2638 started this thread.
    SMF Badges of Honor

    Member since
    Jul 2020
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I’ve dug a whole in the ground outside. It’s solid clay. I’m tempted to put groves around it, wedge in the electric heating element and use insulation as a lid.

    Do you reckon the clay earth would be a good insulator?

  10. #10
    WhiteSquirrel's Avatar
    SMF Badges of Honor

    Member since
    May 2020
    Location
    Ontario, Canada
    Posts
    101
    Thanks
    17
    Thanked 123 Times in 61 Posts
    Not a good insulator (by today's standards), but it'll do the trick - specially just for Alum. They used to melt all kinds of metal in holes in the ground back when my dad was chasing down mammoths, might just take a little bit longer. I still use my home made charcoal to melt 75% of my Alum, just like those good ol days :P
    Last edited by WhiteSquirrel; 07-07-2020 at 04:17 PM.


  11. Similar threads on the Scrap Metal Forum

    1. Aluminium and copper going up!
      By hobo finds in forum Scrap Metal Prices
      Replies: 3
      Last Post: 08-10-2017, 03:21 PM
    2. This thead is a question - LME Aluminium Alloy and Aluminium Ingot Price Levels
      By AAInt in forum Scrap Metal Prices
      Replies: 7
      Last Post: 10-29-2015, 07:03 AM
    3. This thread has a tip for you - Ford's 2015 aluminium 150
      By EcoSafe in forum General - Let's talk business
      Replies: 4
      Last Post: 10-05-2014, 02:28 AM
    4. Aluminium Cans
      By Dags in forum General - Let's talk business
      Replies: 1
      Last Post: 11-15-2010, 08:47 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook