Page 1 of 2 12 LastLast
Results 1 to 20 of 21

Is it Brass or Stainless Steel?

| Scrap Metal Questions and Answers
  1. #1
    philshark2 started this thread.
    philshark2's Avatar
    SMF Badges of Honor


    Member since
    Aug 2014
    Location
    Lake Elsinore CA
    Posts
    126
    Thanks
    13
    Thanked 67 Times in 31 Posts

    Is it Brass or Stainless Steel?

    Hey all, I recently acquired a few faucets I finished taking them apart and I did a scratch test to identify the faucets. First few scratches revealed a layer of copper, but further scratching revealed white metal. I hit it with a grinder and no sparks came out, so I am having doubts that it is stainless steel. Please help me identify these faucets.
    Last edited by philshark2; 02-08-2018 at 10:53 PM.


  2. #2
    msmoorad's Avatar
    SMF Badges of Honor


    Member since
    Apr 2013
    Location
    Durban, South Africa
    Posts
    689
    Thanks
    713
    Thanked 746 Times in 356 Posts
    since brass is much more expensive than s/steel, i would just put it into my brass lot and forget about it.

    its highly unlikely that ts any other metal
    and besides, its already damaged by the grinder so its not like u can resell it

  3. #3
    hills's Avatar
    SMF Badges of Honor



    Member since
    Sep 2017
    Location
    Maine
    Posts
    1,351
    Thanks
    797
    Thanked 1,276 Times in 721 Posts
    It's NOT common ... but sometimes faucets are made of platinum. I only saw platinum faucets used on one high end job during the 30 years i was in the trade but they are out there. Nickel might be another possibility for the white metal underneath ?

    Any info on what kind of place the faucet came out of ? Maybe look on the faucet for brand name, model #, and any hallmarks ?

  4. #4
    t00nces2's Avatar
    SMF Badges of Honor


    Member since
    Jul 2014
    Location
    Sarasota, FL
    Posts
    1,693
    Thanks
    1,187
    Thanked 2,341 Times in 958 Posts
    Looks like brass. The parts you ground look yellow.

  5. #5
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    looks like stainless with a brass coating?
    Better than the dump!

  6. #6
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,873
    Thanks
    1,638
    Thanked 1,733 Times in 893 Posts
    Some of the cheap-o faucets can be cast alum

  7. The Following 3 Users say Thank You for This Post by greytruck:


  8. #7
    ragstoriches's Avatar
    SMF Badges of Honor

    Member since
    Oct 2015
    Location
    Western MA
    Posts
    134
    Thanks
    448
    Thanked 180 Times in 70 Posts
    I always assumed they were a mix of metals and were zinc based.

  9. #8
    SMF Badges of Honor

    Member since
    Apr 2013
    Location
    western ny
    Posts
    83
    Thanks
    134
    Thanked 123 Times in 56 Posts
    Cast aluminum. Stainless would be heavy and limited use in residential. File test: aluminum is soft, stainless is hard.

  10. The Following User Says Thank You to btkr for This Post:


  11. #9
    dsroten's Avatar
    SMF Badges of Honor


    Member since
    Apr 2015
    Location
    NC, United States
    Posts
    83
    Thanks
    25
    Thanked 141 Times in 50 Posts
    Cast aluminum in all likelihood. Take a nice deep cut with file. Shiny chrome on outside, then brass, then white and shiny again. The thin layer of brass is there for the chrome plating process I think. As was said above, you get a feel for the way a file digs into aluminum and skates across stainless.

  12. #10
    SMF Badges of Honor

    Member since
    Sep 2013
    Posts
    95
    Thanks
    0
    Thanked 84 Times in 42 Posts
    It is a zinc based die cast metal. Many of the newer ones are die cast. I think technology and cost got to where the companies switched. 99% of consumers don't care anyway. Always great to get an older brass one. Aluminum is too reactive to water and will corrode out. Stainless isn't normally cast and is not machineable enough for mass production. The brass/copper layers are normally for the chrome plating process. Sometimes, depending on how they are set up internally, for instance the faucet will prob have a brass tube to the spigot while the handles or cover plate will be just die cast, the yard will buy them for brass breakage. It all depends on the component construction. Most faucets aren't terrible to take apart.

    While we are at it, I've seen a few comments on here and heard some on the street along the lines of "If I never learn what something really is, then it's ok to just throw it in the bucket I think it should be in"...I'm not ok with that personally. It's pretty unethical to me. It's ok to learn and ask questions. Sure, you might be disappointed. But probably just once. You won't keep thinking "wow this is a brass faucet" everytime only to have the yard burst your bubble. You will know to have tempered expectations and maybe get lucky. Frankly, if you learn, you can sometimes find things that are MORE valuable than you think. Those old coffee pots from the perculator days....just stainless right? WRONG. I've gotten more than one that looks as chromed out as 99% of the stainless ones only to file and find out it was copper...

    By the way, the resell on faucets, unless you just come across something incredibly vintage or TOP of the line is just awful. Sort of frustrating when you consider how much they cost...but, I guess it's like HVAC units...they know you only buy them a few times in your life at most, so got to keep the workers employed and the factory open somehow.
    Last edited by ozarksewaste; 02-10-2018 at 07:32 AM.

  13. The Following 3 Users say Thank You for This Post by ozarksewaste:


  14. #11
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    Hit it with a hammer die cast zinc will break, stainless will not.

  15. The Following 2 Users say Thank You for This Post by hobo finds:


  16. #12
    hills's Avatar
    SMF Badges of Honor



    Member since
    Sep 2017
    Location
    Maine
    Posts
    1,351
    Thanks
    797
    Thanked 1,276 Times in 721 Posts
    There have been some trends in faucets over the last 20 years. The real cheapos are made of plastic and plated with chrome. There's an issue with brass because the lead in the alloy leaches out into the drinking water. The EPA has made such a fuss about all brass fittings that it's probably illegal to manufacture a brass faucet now.

    It used to be that a faucet was intended to last a very long time. Plumbers had the repair parts and knew how to replace washers, cartridges, and even valve seats. It took a bit of skill and specialized tools to install a faucet. That's all changed now. Maybe you get five years of use and then replace them with the ones from the big box stores. The faucets have been redesigned. They're not hard to change out. It's a lot more time efficient ( and profitable ) for a plumber to swap one out than it is to fiddle around with repair parts that might or might not get the job done right.



    Point being: You're less apt to see brass faucets these days. More likely something else once you scratch the surface.

  17. The Following User Says Thank You to hills for This Post:


  18. #13
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    Quote Originally Posted by hills View Post
    There have been some trends in faucets over the last 20 years. The real cheapos are made of plastic and plated with chrome. There's an issue with brass because the lead in the alloy leaches out into the drinking water. The EPA has made such a fuss about all brass fittings that it's probably illegal to manufacture a brass faucet now.

    It used to be that a faucet was intended to last a very long time. Plumbers had the repair parts and knew how to replace washers, cartridges, and even valve seats. It took a bit of skill and specialized tools to install a faucet. That's all changed now. Maybe you get five years of use and then replace them with the ones from the big box stores. The faucets have been redesigned. They're not hard to change out. It's a lot more time efficient ( and profitable ) for a plumber to swap one out than it is to fiddle around with repair parts that might or might not get the job done right.

    Point being: You're less apt to see brass faucets these days. More likely something else once you scratch the surface.
    Yep they say the plastic ones are the only faucets that are lead free...

  19. #14
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    I don't know much about plumbing, but I'm a expert when it comes the Steel taps..

    Yes, I'm a 'Ferrous Faucet Major.'

  20. The Following 3 Users say Thank You for This Post by eesakiwi:


  21. #15
    t00nces2's Avatar
    SMF Badges of Honor


    Member since
    Jul 2014
    Location
    Sarasota, FL
    Posts
    1,693
    Thanks
    1,187
    Thanked 2,341 Times in 958 Posts
    Quote Originally Posted by eesakiwi View Post
    I don't know much about plumbing, but I'm a expert when it comes the Steel taps..

    Yes, I'm a 'Ferrous Faucet Major.'
    Groan...

  22. #16
    Breakage's Avatar
    SMF Badges of Honor

    Member since
    Aug 2016
    Posts
    297
    Thanks
    242
    Thanked 273 Times in 149 Posts
    Others may not value this method but, holding the faucet by a thin edge, strike it with a small hammer or knock it against a metal surface. Aluminum clunks, steel chimes, copper hums, and brass rings. It's not 100% but, since I rarely have a grinder to test things offsite, this method lets me do some initial sorting, at least enough to know if it should or shouldn't go in the ferrous pile.

  23. The Following 2 Users say Thank You for This Post by Breakage:


  24. #17
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,873
    Thanks
    1,638
    Thanked 1,733 Times in 893 Posts
    Quote Originally Posted by Breakage View Post
    Others may not value this method but, holding the faucet by a thin edge, strike it with a small hammer or knock it against a metal surface. Aluminum clunks, steel chimes, copper hums, and brass rings. It's not 100% but, since I rarely have a grinder to test things offsite, this method lets me do some initial sorting, at least enough to know if it should or shouldn't go in the ferrous pile.
    good point,

    Sometimes i just drop mystery scrap pieces on the cement floor to determine what metal it is by the sound. Ding, Dong, whos at the door????

  25. #18
    SMF Badges of Honor

    Member since
    Nov 2017
    Location
    Australia
    Posts
    18
    Thanks
    0
    Thanked 2 Times in 2 Posts
    Not doubt! It is brass...........

  26. #19
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    Quote Originally Posted by amirycashforcars View Post
    Not doubt! It is brass...........
    Except for the metal under the brass coating... look again at 2nd pic

  27. The Following User Says Thank You to hobo finds for This Post:


  28. #20
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,873
    Thanks
    1,638
    Thanked 1,733 Times in 893 Posts
    I wonder what he ever decided it was......

  29. The Following 2 Users say Thank You for This Post by greytruck:



  30. Similar threads on the Scrap Metal Forum

    1. Stainless steel
      By rooka21 in forum Scrap Metal Questions and Answers
      Replies: 32
      Last Post: 04-27-2022, 03:49 PM
    2. Is it Stainless Steel, Chrome-plated Brass or Aluminum?
      By Mick in forum Scrap Metal Tips and Advice
      Replies: 15
      Last Post: 09-26-2014, 09:12 AM
    3. This thead is a question - Stainless Steel what to do
      By skipster316 in forum Scrap Metal Questions and Answers
      Replies: 19
      Last Post: 12-13-2013, 03:26 PM
    4. I googled before I posted: stainless or brass? 318 L and 308 CGA 626
      By scrapperjames in forum Scrap Metal Questions and Answers
      Replies: 5
      Last Post: 11-22-2013, 04:23 PM
    5. Non magnetic silver nuts, if not brass are they stainless?
      By newattitude in forum Scrap Metal Questions and Answers
      Replies: 10
      Last Post: 11-16-2011, 03:52 PM

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook