Results 1 to 14 of 14

Winch for general use?

| Scrap Metal Questions and Answers
  1. #1
    Hiccup started this thread.
    SMF Badges of Honor


    Member since
    Aug 2012
    Location
    US
    Posts
    30
    Thanks
    24
    Thanked 18 Times in 12 Posts

    Winch for general use?

    Thinking about mounting a winch to my trailer for general use any suggestions and reasoning for a min. Load rating?



  2. #2
    Libertytow's Avatar
    SMF Badges of Honor

    Member since
    Sep 2012
    Location
    Silverton NJ
    Posts
    562
    Thanks
    64
    Thanked 340 Times in 180 Posts
    anything but hf badlands
    Liberty Towing & Recycling
    (732)279-8599
    Cleaning up NJ 1 LB at a time!
    Certified Mobile Scales
    Fully Insured Carrier usdot # 1802487
    WWW.LibertyTowing.Webs.Com
    WWW.TRRecycles.Webs.com

  3. #3
    Hiccup started this thread.
    SMF Badges of Honor


    Member since
    Aug 2012
    Location
    US
    Posts
    30
    Thanks
    24
    Thanked 18 Times in 12 Posts
    Ok so I'm thinking that 2500 lb would be good for general use and pulling stuck items.

  4. #4
    SMF Badges of Honor


    Member since
    Oct 2010
    Posts
    234
    Thanks
    71
    Thanked 195 Times in 90 Posts
    If you plan on winching up vehicles(I have no idea if you do or don't) then 2500 isn't going to cut it. I use a 10 000 lb Superwinch on my car trailer, and even with a snatch block it's really had to strain on some deeply stuck vehicles, especially old tractors that have been sitting in the same soft farmer's field for the last 30 years. So you may wish to consider a heavier winch. It's better to have it and not need it, than need it and not have it.

    The winch on the car trailer is a Superwinch. I bought that brand because it was cheap, $300 for a 10k winch so I also bought a spare right away. But it's still a brand name that I trust to be somewhat reliable, unlike the stuff you get at Costco or Princess Auto. I stayed away from the better brands like Warn or Ramsey, even though they're more reliable IMO, because they're a bigger target/magnet for thieves. That's something I have to keep in mind, living in a big city with my trailers parked in a yard in an industrial area.

    The winch I use on my dump trailer is an 8000lb Warn. It's not permanently mounted however, so it usually rides in the back seat of the truck until its needed. It's mounted on a steel plate mount that's welded onto the slide-in part of a receiver hitch. The receiver hitch itself is just an old hitch from a vehicle I scrapped, mounted on the front of the trailer and reinforced with some steel arms. Its awesome when you need it, like loading a big piece of scrap equipment from a place that has no forklift to load you. Its even come in really handy just securing down an awkward load with the cable. Each side of the trailer has tie-down eyelets mounted that are big enough to work the cable hook through, so I can zigzag it around if needed. You might want to consider keeping your winch removeable like that, if you don't expect to use it all the time. Keeps it out of the weather, and keeps it out of sight out of mind.

    When you mount whatever winch you go with, have a secure snatchblock mount done right away too. It doubles your winch's power, and can come in super handy. Lastly, powering your winch. When I got the winch mounted on the car trailer, I mounted a battery and had the wiring done to keep it charged off the vehicle. That didn't work out well for me. Batteries wouldn't stay charged, and I killed a few before I gave up. I'm sure it's just a bad ground(s) somewhere, but hell if I can find where. Even the factory charging circuit on the dump trailer is a dud. And talking with other scrappers, its a common problem. So now I just run the winch on either trailer directly off a battery. I use a deep cycle group-31 sized battery (that's the battery size for big trucks). It lasts quite a while. For charging, I either take it home at night and throw it on a charger, or if I'm going to be somewhere a while, while loading or something, I'll just boost it off the truck. To connect the winch to the battery I use those large plastic 2-cable plugs like what are used to hook up the battery on an electric forklift, or you see the same plugs on the front of tow trucks to plug their booster cables into.
    Hope this helps.
    Last edited by zito; 01-26-2013 at 01:06 PM.

  5. The Following 2 Users say Thank You for This Post by zito:


  6. #5
    BurlyGuys's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Location
    Waterford Michigan
    Posts
    1,591
    Thanks
    1,109
    Thanked 1,620 Times in 635 Posts
    Hm. I have a small winch on my stake truck. For power I just hook jumper cables from the battery in my truck to the terminals on the winch. Is there any reason NOT to do that?
    Burly Smash![/COLOR][/SIZE][/FONT]
    John Terrell (248) 224-2188
    Burly Guys Junk Removal LLC
    5499 Perry Drive Unit P Waterford, MI 48329
    http://www.burlyguys.com

  7. #6
    SMF Badges of Honor


    Member since
    Oct 2010
    Posts
    234
    Thanks
    71
    Thanked 195 Times in 90 Posts
    Quote Originally Posted by BurlyGuys View Post
    Hm. I have a small winch on my stake truck. For power I just hook jumper cables from the battery in my truck to the terminals on the winch. Is there any reason NOT to do that?
    That's a lot more load than your alternator is designed for. It's really hard on the alternator as well as being hard on the battery. This was explained to me by my battery guy (he's the guy I sell my scrap batteries to. He has a shop selling batteries, both automotive as well as doing a lot of off-grid stuff. He's also a licensed mechanic), and was confirmed by the owner of a small local shop that rebuilds starters, alternators, and motors. It's something that done enough, over time, will wear stuff out a lot quicker.

    Don't get me wrong; it's something I've done myself before, and still do from time to time when I'm in a pinch, like say I've forgotten to charge a battery or forgotten the spare battery itself. But considering the winch is something I use a lot, I do whatever I can that minimizes (or even just -maybe- minimizes) the chances of something screwing up at a really inconvenient time.
    Last edited by zito; 01-26-2013 at 02:09 PM.

  8. #7
    JohnC4X4's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    South East Ma
    Posts
    986
    Thanks
    162
    Thanked 1,127 Times in 514 Posts
    Quote Originally Posted by zito View Post
    That's a lot more load than your alternator is designed for.
    The alternator is designed to put out X amount of amps
    It will do this no matter what the load is on the Battery
    If your total electrical load is greater then the Alternator puts out, then the current comes from the Battery
    When the load reduces > Winch in off position, Battery recharges

    Snow plows are now Electric over Hydraulic
    Meaning there is a DC motor that operates the Hydraulic pump to position the plow
    If doing small lots with a lot of re angling of the plow, sometimes you need to sit for a couple mins with the engine at high idle to recharge the Battery
    LARGE Electrical load when plowing at night >> Heater blower on high, Heated seats on high, Mirrors defrost on, Light Bar going at full blast
    For some reason Ford no longer puts a Voltage meter in the dash, so I have learned when the voltage drops the radio cuts out, time to idle for a couple mins

    So when I pull a junk car onto the trailer,
    I have a Battery in the trailer that operates the Hydraulics's and both winches
    I have a Harbor Freight 12K for over 2 years and no problems and for the last 20 years have used the Ramsey 8K REP >> They seem to last 3 - 4 years between needing motors

    The connection I use for the power to the trailer is a jump system
    Lexan Plug Jump-Start Set with 500 Amp Clamps - Superior Signals | AW Direct

    I have a plug setup in front and rear of the truck
    Single Replacement Plug End - Superior Signals | AW Direct


    I keep my trucks for about 7 years and they get between 230K and 250K on them before I sell them
    This is my third Ford SD >> Had 95, 02 and the current 08 >> I have never had to replace an alternator
    I do go thru Batteries about every 3 years >> I like the Sears Die Hard for the Warranty

  9. The Following User Says Thank You to JohnC4X4 for This Post:


  10. #8
    SMF Badges of Honor


    Member since
    Oct 2010
    Posts
    234
    Thanks
    71
    Thanked 195 Times in 90 Posts
    Thanks JohnC, learn something new every day. As I say, that's how it was explained to me, and it seems to make sense to me. Even if it's just a placebo effect, it's how I'll keep doing it for peace of mind. I mean, even worst case scenario, I can't go wrong by carrying an extra battery around with me.

  11. #9
    SMF Badges of Honor

    Member since
    Mar 2012
    Location
    Chesaning
    Posts
    472
    Thanks
    24
    Thanked 355 Times in 171 Posts
    I have 2 HF badlands 12k. I've broke a few but with the 2 year warranty they just give you a new one. It is worth the money. I also have a group 31 battery on both of my trailers. Then I gave my plug wired up so it charges my battery as I'm driving down the road.

  12. #10
    Otto's Avatar
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    Ottawa, Ontario
    Posts
    335
    Thanks
    494
    Thanked 322 Times in 166 Posts
    John and resourceful, if I'm understanding your set ups correctly, you're running your truck and trailer batteries in parallel. Should give you lots of juice for your winch or do you unplug the truck-trailer connection before running the winch? Battery banks for back-up power use this arrangement.

  13. #11
    JohnC4X4's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    South East Ma
    Posts
    986
    Thanks
    162
    Thanked 1,127 Times in 514 Posts
    Quote Originally Posted by Otto View Post
    John and resourceful, if I'm understanding your set ups correctly, you're running your truck and trailer batteries in parallel.
    Correct for me

  14. #12
    SMF Badges of Honor

    Member since
    Mar 2012
    Location
    Chesaning
    Posts
    472
    Thanks
    24
    Thanked 355 Times in 171 Posts
    Yep, same with me.

  15. #13
    Otto's Avatar
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    Ottawa, Ontario
    Posts
    335
    Thanks
    494
    Thanked 322 Times in 166 Posts
    Just one caution with this set up though - with the extra current available from the two batteries, you need to ensure you have overcurrent protection (fusing) for your winch so you don't smoke it under heavy load. Consult your owner's manual or contact the manufacturer.

  16. #14
    sledge's Avatar
    SMF Badges of Honor


    Member since
    Nov 2012
    Location
    Central Indiana
    Posts
    2,717
    Thanks
    4,534
    Thanked 4,240 Times in 1,609 Posts
    Engo Winches: I did a TON of research on winches and found that these badboys are reasonably priced and tough as nails. I have a 10,000 lb winch on my 16 ft trailer and I think shipped to my door it was about $340! I highly recommend em!


  17. Similar threads on the Scrap Metal Forum

    1. new winch and new advertising
      By corycouch in forum A Day in the Life of a Scrapper
      Replies: 26
      Last Post: 01-25-2013, 10:15 PM
    2. PTO Winch Adaptations
      By huntsman in forum Tools and Equipment
      Replies: 0
      Last Post: 07-02-2012, 10:38 AM
    3. I've really got to get a winch put on my truck
      By newattitude in forum A Day in the Life of a Scrapper
      Replies: 1
      Last Post: 02-15-2012, 10:14 PM
    4. New Winch
      By Semo Scrapper in forum Tools and Equipment
      Replies: 3
      Last Post: 03-10-2011, 06:27 PM
    5. Winch...who has the best brand?
      By IdahoScrapper in forum General - Let's talk business
      Replies: 2
      Last Post: 12-16-2010, 07:46 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook