Results 1 to 8 of 8

black cast help

| Scrap Metal Identification
  1. #1
    cummins started this thread.
    cummins's Avatar
    SMF Badges of Honor


    Member since
    Apr 2013
    Location
    ontario
    Posts
    573
    Thanks
    15
    Thanked 255 Times in 171 Posts

    black cast help

    Can any one help me with the difference between black cast and regular cast iron. Noticed black cast was at 1.70 a pound. Might have a concetion to buy a couple completely striped cracked cat blocks. They've even been through the Sault tank and are clean.



    Haven't had much luck on Google mostly pots and pan and maker markings haven't found anything about engine blocks yet. Thanks for the help


  2. #2
    SMF Badges of Honor



    Member since
    Apr 2015
    Posts
    2,072
    Thanks
    615
    Thanked 2,445 Times in 1,092 Posts
    Quote Originally Posted by cummins View Post
    Can any one help me with the difference between black cast and regular cast iron. Noticed black cast was at 1.70 a pound. Might have a concetion to buy a couple completely striped cracked cat blocks. They've even been through the Sault tank and are clean.

    Haven't had much luck on Google mostly pots and pan and maker markings haven't found anything about engine blocks yet. Thanks for the help
    No way your getting $1.70 lb for black cast, think you may have meant $1.75 per hundred weight, $35.00 short ton.

    Black cast would be soil pipe aka sewer, stove cast and probably include bath tubs and sinks and hot water radiators.
    Last edited by alloy2; 01-18-2016 at 10:06 PM.

  3. The Following User Says Thank You to alloy2 for This Post:


  4. #3
    cummins started this thread.
    cummins's Avatar
    SMF Badges of Honor


    Member since
    Apr 2013
    Location
    ontario
    Posts
    573
    Thanks
    15
    Thanked 255 Times in 171 Posts
    I took a load of hms 1 in Friday had a look at the price sheet while I was waiting for my paper work. 160 ton. Asked about striped engine blocks from cat and she said some of the high out put blocks are black cast and they would test them first. News to me. Figured I ask here. Grey and black cast are different . Trying to figure easy way to tell so I don't buy and lose money.

  5. The Following User Says Thank You to cummins for This Post:


  6. #4
    cummins started this thread.
    cummins's Avatar
    SMF Badges of Honor


    Member since
    Apr 2013
    Location
    ontario
    Posts
    573
    Thanks
    15
    Thanked 255 Times in 171 Posts
    170 a ton sorry

  7. #5
    SMF Badges of Honor



    Member since
    Apr 2015
    Posts
    2,072
    Thanks
    615
    Thanked 2,445 Times in 1,092 Posts
    Quote Originally Posted by cummins View Post
    I took a load of hms 1 in Friday had a look at the price sheet while I was waiting for my paper work. 160 ton. Asked about striped engine blocks from cat and she said some of the high out put blocks are black cast and they would test them first. News to me. Figured I ask here. Grey and black cast are different . Trying to figure easy way to tell so I don't buy and lose money.
    Your yard probably used a hand held XRF to determine the alloy composition of any cast suspect of being high grade.

    What they're looking for is Chromium and Nickel or a combination.

    This type of cast at the foundry is worth in the neighbourhood of $800.00 ton and is used in high heat applications requiring abrasion resistance like large pumps used in the mining industry. Some English gasoline and diesel engine blocks had a high chromium content,

    Chevy small block with 010 cast into the blocks have a high nickel content.

    Some but not all diesel engine cylinder liners could be made from a chromium / cast iron alloy.

    There are methods of identifying a metals composition using acids which are considered non destructive.

    https://books.google.ca/books?id=jEv...alloys&f=false
    ,
    Abrasion resistant cast irons/
    Casting Material: Abrasion-Resistant Cast Iron 12% Cr : Sand Casting, Investment Casting and Die Casting in China
    Last edited by alloy2; 01-19-2016 at 02:53 AM.

  8. The Following 8 Users say Thank You for This Post by alloy2:


  9. #6
    SMF Badges of Honor



    Member since
    Apr 2015
    Posts
    2,072
    Thanks
    615
    Thanked 2,445 Times in 1,092 Posts
    The skinny on GM engine blocks alloyed with nickel.

    Identify the block casting number, which you can find on the top of the bell-housing ridge (where the transmission connects). If you see a "++" after the casting number, then it's a high-nickel block.

    Remove the harmonic balancer and crankshaft pulley from the front of the crankshaft. Remove the water pump and timing cover from the front of the engine. Identify the block casting just above the crankshaft main journal.

    Note the numbers you see there. They indicate the block's nickel and tin content by volume. If you see an 010 and 020, the block has 10 percent tin and 20 percent nickel by volume.

    An 010 or 020 by itself indicates the block's nickel content as 10 or 20 percent, respectively.

    Read more : How to Identify a Small Block and a High Nickel Block on a Chevy | eHow the block casting number, which you can find on the top of the bell-housing ridge (where the transmission connects). If you see a "++" after the casting number, then it's a high-nickel block.

    Remove the harmonic balancer and crankshaft pulley from the front of the crankshaft. Remove the water pump and timing cover from the front of the engine. Identify the block casting just above the crankshaft main journal.

    Note the numbers you see there. They indicate the block's nickel and tin content by volume. If you see both an 010 and 020, the block has 10 percent tin and 20 percent nickel by volume. An 010 or 020 by itself indicates the block's nickel content as 10 or 20 percent, respectively.



    Read more : How to Identify a Small Block and a High Nickel Block on a Chevy | eHow

  10. The Following 2 Users say Thank You for This Post by alloy2:


  11. #7
    SMF Badges of Honor

    Member since
    Apr 2012
    Location
    Maple Ridge, BC, Canada
    Posts
    254
    Thanks
    103
    Thanked 306 Times in 125 Posts
    ALL Chrysler/Dodge V8 engine blocks from 60's to mid-late 70's (at least) are also high nickel.

  12. #8
    SMF Badges of Honor



    Member since
    Apr 2015
    Posts
    2,072
    Thanks
    615
    Thanked 2,445 Times in 1,092 Posts
    Simple solution to problem just ask the yardman to see an inventory of their black cast then ask for or purchase a small sample to perform some acid testing on.

    Nitric acid is commonly used to identify metals, a small drop onto a filed clean surface free of oil will produce colors specific of those used in the alloyed metal. Adding a bit of heat will definitely speed up the chemical reaction.

    If your paranoid of using acids use a grinder for spark testing.

    Identifying metals for welders, good information for the scrapper.

    Lots of charts. Metal Composition: Analysis , Tests and Charts

    Metal Tests : How To Identify Metals For Welding : Maine Welding Company


    Last edited by alloy2; 12-14-2016 at 03:34 PM.


  13. Similar threads on the Scrap Metal Forum

    1. aluminum prices cast versus die cast
      By endmill in forum Scrap Metal Prices
      Replies: 11
      Last Post: 04-04-2014, 09:10 AM
    2. black friday
      By tsmith53149 in forum Off Topic Discussions
      Replies: 11
      Last Post: 11-24-2013, 03:36 PM
    3. Black walnut
      By Copper Head in forum A Day in the Life of a Scrapper
      Replies: 14
      Last Post: 10-23-2011, 10:26 PM
    4. Harddrives.... Cast or Die Cast?
      By Recyclinggirlie in forum Scrap Metal Tips and Advice
      Replies: 15
      Last Post: 10-20-2011, 10:02 AM
    5. Old cast iron motosr and how to tell cast iron from steel ?
      By Ironhead in forum Misc. Metal Recycling
      Replies: 2
      Last Post: 06-13-2011, 07:05 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook