Page 2 of 2 FirstFirst 12
Results 21 to 30 of 30

Hard drive destruction - Page 2

| Scrap Business Ethics
  1. #21
    matador's Avatar
    SMF Badges of Honor

    We purchase laptop computers and many components for greater than scrap value. We offer a shipping reimbursement program.replies

    Member since
    Nov 2013
    Location
    Big Wonderful Wyoming
    Posts
    2,310
    Thanks
    1,813
    Thanked 3,204 Times in 1,450 Posts
    PTS is right- if you have $8500.

    If you have a log splitter, you're good to go. For the average person though, it's not feasible to buy a machine like that until you're doing this a lot.

    For most drives, bending should be enough. If not, disassemble them, cut the platters into quarters, and mix them.



  2. #22
    ThatTubaDude started this thread.
    ThatTubaDude's Avatar
    SMF Badges of Honor


    Member since
    Jun 2014
    Posts
    69
    Thanks
    4
    Thanked 68 Times in 31 Posts
    Thank you all very much, I am not contractually obligated to destroy all of them but I am doing my best to be ethical because I work off of a handshake and a verbal agreement. I will probably just break them down and break the platters

  3. #23
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    Quote Originally Posted by bcrepurposing View Post
    i have commented in past on this but will repeat a bit of what i said before.

    removing the boards will deter a average person. not a person intent retreaving your data. it is possible to figure out what board belongs there by trial error on known used parts.
    my suggestion comes from experiance. i have 13 years as a repair tech and have done data recovery / sent out mangled devices for recovery so know whats possible.

    .
    It's really not like what you're making it out to be. The most common reason that HDD's die is because of a circuit failure on the logic board somewhere. As hard drive repair goes it's a relatively simple fix.

    1: You look at ALL of the information on the front of the drive and locate an identical drive that was manufactured in the same month.

    2: There's something like a ROM chip on the circuit board. That stores information that is almost unique to that particular drive. (It's something like a fingerprint.) The information tells the rest of the drive where to go and what to do.

    Without that (specific) information the drive will spin up and sit there clicking.

    3: The easiest way to transfer that ROM data over to your donor board is to send it out to a company with the equipment to do that job.

    Here's where the problem comes in : Somebody hands you a random hard drive where the logic board is completely missing !

    The level of difficulty just increased tenfold. All of that ROM information is lost. It takes very specialized equipment to re-discover it.

    You're looking at a capital outlay of around 20 grand for that kind of gear and years of training in HDD repair.

    True .... it can be done, but why on earth would somebody go to all the trouble for a criminal enterprise ?

    There's tons more money to be made in legitimate data recovery and no risk of prosecution.

  4. #24
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    You're looking at a capital outlay of around 20 grand for that kind of gear and years of training in HDD repair.
    True .... it can be done, but why on earth would somebody go to all the trouble for a criminal enterprise ?
    There's tons more money to be made in legitimate data recovery and no risk of prosecution.
    Like was stated earlier, especially for a regular Joe Blow's hard drive. Now if it belonged to Nasa or our military, hospital etc. then it would be a little stricter policy.
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.

  5. #25
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    No doubt Mech .....

    You just do what's appropriate for the job. Scrapping is production work so there's no sense in getting bogged down with drilling & fussing with a run of the mill hard drive.

    Let's say you were doing curbco and parting out the pc's: You should be able to do do the break down in about ten minutes. From there you sell the component parts to the scrap yard.

    Take it a little further: You want to insure that the creepy guy at the junkyard isn't browsing the hard drives. It's really easy to disable the HDD before you sell it. All you have to do is run a utility knife up one side of one of the flat packs and cut the legs.

    It only takes three seconds. You don't even have to fuss with removing the board. You can sell the hard drive whole, get a better price, and do the right thing all at the same time.

    Turn -n- Burn !

    Certified data destruction is something completely different than what your average scrapper needs to worry about.

  6. The Following 2 Users say Thank You for This Post by Scrappah:


  7. #26
    Victor's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    Vegas via Canton Ohio
    Posts
    169
    Thanks
    13
    Thanked 160 Times in 79 Posts
    I have a two step method on the platters.

    Remove logic board and break down drive into it's pieces/parts. Currently I touch both platter surfaces to a belt sander with a 36 grit belt. Get them scratched up using a circular motion of the platter on the belt. Then they are cut into quarters with industrial tin snips. It's slow and labor intensive. Might try a flap wheel on a air tool for 2015. Would like to find a small industrial shear for cutting as well. For now it's what works.

    I will add that I do this for my customers that require advanced destruction. Everyone else gets the same treatment but I leave out the sanding part. Cut in quarters and move on.
    Last edited by Victor; 12-15-2014 at 10:33 AM. Reason: Added info

  8. #27
    FilthyClean's Avatar
    SMF Badges of Honor


    Member since
    Jun 2015
    Location
    Newfoundland
    Posts
    24
    Thanks
    14
    Thanked 39 Times in 8 Posts
    Quote Originally Posted by spinroch View Post
    As olddude says, A stick of dynamite will work, too!
    hahahah ... indeed it does. lol

  9. #28
    SMF Badges of Honor


    Member since
    Jun 2012
    Location
    Pinellas County, FL (formerly Long Island, NY)
    Posts
    87
    Thanks
    6
    Thanked 71 Times in 24 Posts
    Someone suggested using a 30/30 rifle, but a 12-gauge shotgun shooting slugs and 00 buckshot would probably work too. That reminds me, I have some hard drives and a Rem 870 12, maybe I should go to the range and have a little fun.

  10. The Following User Says Thank You to JunkmanDan for This Post:


  11. #29
    SMF Badges of Honor

    Member since
    Jul 2015
    Location
    Palm Coast, FL
    Posts
    55
    Thanks
    94
    Thanked 31 Times in 12 Posts
    The glass platters are worth money intact though. Try **** you can sell 'em by the pound there. I think they have silver on them or something. I don't know if they buy broken platters, you should check before destroying. Just check: Platters go for 0.35/lb on *****
    Last edited by Mechanic688; 08-09-2015 at 12:38 PM. Reason: Removed ewaste buyer not of our forum

  12. #30
    webuyselltradestuff's Avatar
    SMF Badges of Honor

    Member since
    May 2013
    Location
    Watkinsville, GA
    Posts
    950
    Thanks
    131
    Thanked 1,284 Times in 583 Posts
    they actually GENERALLY have minute amounts of platinum and cobalt in the coating.....thought I would clear that up
    PROFIT is made when you BUY/ACQUIRE NOT when you sell


  13. Similar threads on the Scrap Metal Forum

    1. Data Destruction on Hard Drives
      By JayBear480 in forum Legal Topics - Laws, Certifications, Contracts etc
      Replies: 11
      Last Post: 10-24-2014, 09:14 AM
    2. Hard Drive Destruction
      By MvPElectronicRecycling in forum Computer Recycling
      Replies: 40
      Last Post: 07-02-2013, 01:09 PM
    3. Certificate of hard drive destruction
      By Lowjack in forum General Electronics Recycling
      Replies: 29
      Last Post: 02-26-2013, 08:44 AM
    4. Documents- Hard Drive Destruction and Properly Recycled.
      By ResourcefulRecycling in forum General - Let's talk business
      Replies: 0
      Last Post: 10-31-2012, 07:03 PM
    5. Hard drive destruction
      By Victor in forum General Electronics Recycling
      Replies: 9
      Last Post: 02-12-2012, 10:18 AM

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook