Results 1 to 12 of 12

Some Gold Tidbits and Where to Find Them,

| Low-Grade Electronics Recycling
  1. #1
    Mechanic688 started this thread.
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts

    Some Gold Tidbits and Where to Find Them,

    I was tearing down some smaller misc. stuff and found a couple of gold tidbits that you might want to look out for.
    These items were on low grade boards. Not much to them but for me it all adds up after awhile.
    First is a small board standing upright inside some computer power supplies. I tear them down to normally pull the wire as they only pay .13 a lb for them.The gold is in the small jumper pins that fasten the small board (about 2"x2") to the main board upright.



    This lil chip comes from the laser mouse (mouses or mice?). It is mounted in the center of the small brown board inside. About the size of a dime. There's more than just a cord inside them. Enjoy,,



    Sorry for the crappy pictures.
    Last edited by Mechanic688; 04-30-2015 at 12:59 AM. Reason: changed pic's
    P & M Recycling - Specializing in E-Waste Recycling.
    If you enjoy your freedom, thank a vet.



  2. #2
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    Mech.

    Anything on the value of an individual pin in the first pic ? The prices for nickel pins plated with gold at 5 ppm seem to be all over the place.

  3. #3
    Mechanic688 started this thread.
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    Quote Originally Posted by Scrappah View Post
    Mech.

    Anything on the value of an individual pin in the first pic ? The prices for nickel pins plated with gold at 5 ppm seem to be all over the place.
    No idea yet, I just keep adding to the OMG jar. Here's a different board. I believe is another mouse board.




  4. The Following 6 Users say Thank You for This Post by Mechanic688:


  5. #4
    Sirscrapalot's Avatar
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    A sandbar off the atlantic..OBX,NC
    Posts
    6,123
    Thanks
    11,885
    Thanked 8,783 Times in 3,854 Posts
    I just keep adding to the OMG jar.

    Full article at Scrap Metal Forum: http://www.scrapmetalforum.com/low-g...#ixzz3Yx7y7nbH


    Bucket Mech, Bucket!



    Sirscrapalot - Founder of the OMG IT"S GOLD!™ bucket.


    PS - Your pics aren't showing for me. Just shows me a cat an says photo not found, this is in the first post. 2nd one displays just fine.

  6. The Following 3 Users say Thank You for This Post by Sirscrapalot:


  7. #5
    Scrappah's Avatar
    SMF Badges of Honor



    Member since
    Jun 2014
    Posts
    1,058
    Thanks
    320
    Thanked 1,419 Times in 676 Posts
    Quote Originally Posted by Mechanic688 View Post
    No idea yet, I just keep adding to the OMG jar.
    In regard to the pins ... it was sort of a leading question. I've been harvesting the pins for awhile and have a couple pounds put up. It's quite labor intensive and it takes a lot of pins to add up to a pound.

    My best understanding so far is that they are generally gold plated nickel. The average plating is put applied at five parts per million by weight. The older,richer, plating with that deeper color was applied at ten parts per million.

    Maybe there's an error in my reasoning somewhere but when i ran the numbers yesterday it came up like this:

    For every pound of pins you come up with five millionths of a pound of gold .... about .78 cents.

    There would actually be more value recovered in nickel.

    When you balance the effort it takes to make a pound against the value recovered you have to decide if the juice is worth the squeeze.

    If it isn't worth doing and you decided not to do it .... that would free up your time to do something else that's more profitable.

    Just a thought ... somebody that's refining pins would probably know better about the yields.

  8. The Following 3 Users say Thank You for This Post by Scrappah:


  9. #6
    SMF Badges of Honor



    Member since
    Jul 2011
    Location
    Jacksonville, NC
    Posts
    4,917
    Thanks
    15,632
    Thanked 5,861 Times in 2,713 Posts
    "There would actually be more value recovered in nickel."

    When you think about the mother boards and the like you can't ignore the value of the copper in them. Mike
    "Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}

    Now go beat the copper out of something, Miked

  10. The Following User Says Thank You to miked for This Post:


  11. #7
    Mechanic688 started this thread.
    Mechanic688's Avatar
    SMF Badges of Honor



    Member since
    Mar 2011
    Location
    Warsaw , Ind. In the heart of the lakes, and down the street from the hotel where Al Capone stayed.
    Posts
    9,568
    Thanks
    11,247
    Thanked 10,730 Times in 4,728 Posts
    I have info to add to this thread. This IC chip came out of an old tv board (solid state) and has a gold legged transistor down in the corner also. I included a picture of the board so people know what to look for. I always look over low grade boards to see what kind of surprises await.



    General idea of what the board looks like.


    The small black transistor in the corner (with white dots) has gold legs.


    I finally figured out the proper setting for my camera for the people that have endured the blurry pic's.

  12. The Following 9 Users say Thank You for This Post by Mechanic688:


  13. #8
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    That part in the mouse. It can be broken down a bit furthur. Its a image sensor and looks quite pretty. It has Gold wires on it, just like a LED, but about 6 or 8 of them.
    Actually image sensors are great Gold wires sources.
    Those camera ones, Office photocopy machines have a larger rectangle one, also very nice looking.
    And computer flatbed scanners have a long strip one with over 250 Gold wires in it.

    Other places I look are contacts on relays, the little block on the boards, normally blue or black.
    Switches, the ones in microwave doors ( mostly Copper/Silver or Silver) and the same switches from dishwashers tend to be Gold ir Gold plated.

    The little switches from behind tapedeck units for switching the FF and Rwd motors on and off. Simikar switches from other places.

    Any switches from high quality electronics. The little block ones with a bunch of switchs on it are great too.
    Mostly the Gold wires are exposed so I keep the strip in its black plastic casing support bar.

  14. The Following 2 Users say Thank You for This Post by eesakiwi:


  15. #9
    mpmgc's Avatar
    SMF Badges of Honor


    Member since
    Jun 2014
    Location
    Cleveland, Ohio
    Posts
    15
    Thanks
    36
    Thanked 6 Times in 4 Posts
    Is gold located on "Diabetic Meters" pcb?

  16. #10
    Breakage's Avatar
    SMF Badges of Honor

    Member since
    Aug 2016
    Posts
    297
    Thanks
    242
    Thanked 273 Times in 149 Posts

    Some Gold Tidbits and Where to Find Them,

    I've been seeing some in diabetic meters and pedometers. Small boards but very evident gold.

    It's hard to tell if it's worth the hassle. Lots of little screws and the boards weigh almost nothing. Plus, the gold looks a little white, like it's a thin plating. But once you pull off the battery, it's a very clean board.

    I put the units, whole, aside, for now. There aren't many of them and they don't take up too much space.

  17. The Following 2 Users say Thank You for This Post by Breakage:


  18. #11
    mpmgc's Avatar
    SMF Badges of Honor


    Member since
    Jun 2014
    Location
    Cleveland, Ohio
    Posts
    15
    Thanks
    36
    Thanked 6 Times in 4 Posts
    Thank You for the information, it helped me out. : )

  19. #12
    Breakage's Avatar
    SMF Badges of Honor

    Member since
    Aug 2016
    Posts
    297
    Thanks
    242
    Thanked 273 Times in 149 Posts
    If you like that, tear into the tape heads of a VRC or tape camcorder, sometime. Puts the "bits" in "tidbits."



  20. Similar threads on the Scrap Metal Forum

    1. Did I Just Find My First Gold Chip?
      By ChesterCopperpot in forum Scrap Metal Tips and Advice
      Replies: 6
      Last Post: 05-12-2015, 03:35 PM
    2. RARE Vintage Gold Dip CPUs. Cant find anything like them online.
      By secondlifeasset in forum E-Waste Grading and Identification
      Replies: 3
      Last Post: 04-24-2015, 08:19 PM
    3. This thead is a question - First Mystery Find - Trash Metal or Gold?
      By Gravitar in forum Scrap Metal Identification
      Replies: 12
      Last Post: 04-17-2013, 12:12 AM
    4. I love it when I clean out an estate and find gold!!!
      By BurlyGuys in forum General - Let's talk business
      Replies: 4
      Last Post: 06-23-2012, 09:43 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook