Page 2 of 2 FirstFirst 12
Results 21 to 24 of 24

How about a small scale shredder for metal? - Page 2

| General - Let's talk business
  1. #21
    Repurposer's Avatar
    SMF Badges of Honor


    Member since
    Sep 2016
    Location
    Mesa, Arizona
    Posts
    185
    Thanks
    56
    Thanked 113 Times in 69 Posts
    I am going to make a small baler for home shop use out of some scrap metal I have in order to bale my copper that does take up lots of space. I am planning on using an 18 inch long piece of heavy wall (say 1/4 inch) square tubing maybe 10 inch ID. I have bigger tubing but that seems to be a good starting point. I have a flat piece of one inch thick steel that will be trimmed to fit in the tubing ID to be the crusher panel and one piece of steel (does not have to be one inch) welded to the bottom. There will also be a thinner (1/4 inch thick minimum) flat piece of steel sitting below the bale. The bottom will have three or four 3/4 inch holes drilled in it (any size holes you want. I am going with 3/4) so it's possible to drive out the bale if it gets stuck. (this is where the thinner piece under the bale comes in to play). Kind of hard to drive against something soft like copper. I have all kinds of number one and two copper but it's various sizes and lengths. I use a harbor freight cable cutter ($14.00 on sale) to easily chop even one inch copper tube in to managable sizes. Most of my copper scrap is already doubled over and will easily fit in the 18 inch depth of the tubing. I have a 20 ton shop press. After dropping the press base down set the baler on it. I have a supply of diesel engine wrist pins various lengths I use on my press. Very strong but other solid steel rod will work or even steel punches at least an inch in diameter. More than strong enough to push down the compactor plate and the copper downward until it stops. Not much pressure is needed. Don't want to smash the copper to death. Just compact it some so it's easier to stack and store and remain identifiable. I plan on compacting it then adding more and crushing it again until I have close to an 18 bale each time. Just one of my ideas to make my life easier. The scrap I will be using to make it cost me nothing. Just stuff I was given to haul away. Forgot to ad. Some kind of lift handle or threaded hole a handle can be threaded in to must be added to the crusher panel so it can be lifted back out.
    Quote Originally Posted by aph View Post
    I keep telling my guys to cut down, clean up non-ferrous as they go along, but nobody listens.
    I have a big pile of copper lines, mostly from dishwashers and they take up a crapload of space.
    I crimp and bend them into 6-8 inch pieces so much more weight fits into the buckets.
    But it is tideous boring A.F. work.
    So I was thinking, is there a small scale metal shredder that would shred my #2 copper lines into smaller chunks?
    I would be willing to pay a few 100 bucks for it since it would save so much time in the long run.
    TIA
    Martin


    Last edited by Repurposer; 10-24-2016 at 04:27 PM.


  2. #22
    SMF Badges of Honor


    Member since
    Oct 2011
    Location
    Canada
    Posts
    169
    Thanks
    29
    Thanked 72 Times in 40 Posts
    Make sure your bale is a loose bale or the yard may not want to buy it in case there is something hidden inside. I had a guy bring me a 4x4x2" block of copper that he baled really tight in an oil filter press. After he left I was looking at it and there was some brass mixed through it that I didn't see when buying it. We made an alligator shear out of some steel plate, thick pipe, truck rim, small cylinder and an old hydraulic power pack that we got in the scrap. works good for what we do with it (chop and clean copper/brass/aluminum). You can take a roll of 3/8 copper and make a cut through the whole roll on both sides then place the two halves together and make a cut through it all at once.

  3. #23
    Repurposer's Avatar
    SMF Badges of Honor


    Member since
    Sep 2016
    Location
    Mesa, Arizona
    Posts
    185
    Thanks
    56
    Thanked 113 Times in 69 Posts
    Yea just a loose bale. Like I said I did not want to crush the devil out of the copper. Just make it more managable and easier to store. I have actually done this before and light can be seen through the bale. Oil filter crushers have some guts for sure. They can flatten the toughest filters. Thanks for the advice though.
    Quote Originally Posted by myekem View Post
    Make sure your bale is a loose bale or the yard may not want to buy it in case there is something hidden inside. I had a guy bring me a 4x4x2" block of copper that he baled really tight in an oil filter press. After he left I was looking at it and there was some brass mixed through it that I didn't see when buying it. We made an alligator shear out of some steel plate, thick pipe, truck rim, small cylinder and an old hydraulic power pack that we got in the scrap. works good for what we do with it (chop and clean copper/brass/aluminum). You can take a roll of 3/8 copper and make a cut through the whole roll on both sides then place the two halves together and make a cut through it all at once.

  4. #24
    ScrapmanIndustries's Avatar
    SMF Badges of Honor


    Member since
    Feb 2017
    Location
    Easton, Pa
    Posts
    361
    Thanks
    99
    Thanked 303 Times in 132 Posts
    Quote Originally Posted by aph View Post
    You are def correct there.
    I do let little things slide here and there and then it turns into a big (pile of half assed processed non-ferrous).
    I am not always around and have 7 m,illion other things going on at any given time.
    Addressing the problem with the employees will have to be the one big step I somehow have to figure out.
    Not using that as an excuse, but it is VERY hard finding any good employee in Central Valley of California.
    Regardless what job I am hiring for, LITERALLY half the people don't even show up for interviews. And that with 10% unemployment.
    And then most feel friggin entitled.
    Unfortunately you have to literally be happy if you find someone that is 80% ok in their performance.
    Yes, it is THAT bad around here.
    I wish I woulda read this Thread back when Western Express dumped me off out there. I'm trying to find a junkyard job currently. And with that being said you can't always expect everyone to look good on paper. Sometimes the best employees you'll find are the ones that look horrible on that black and white slip they hand you, mostly cause they'll be desperate to keep that job. And I don't see why unemployment makes people wanna not hire someone. Not everyone thats unemployed is unemployed because of their choosing, and the one thing that makes unemployment harder to get get out of is that no one wants to hire you when your unemployed. I've been struggling for like a whole year now to find a job after I got out of the army. I was so broke for awhile I kept taking jobs I really wasnt good at, or couldnt afford to stay at long and now its even harder to find a job since i didn't perform well at my last 3 jobs and pretty much got fired. Does this affect my performance at my next job? No but alot of HR reps/ possible future employers beg to differ. Ive had 8 different jobs in 2016, and after this temp thing is over with the state it looks like I might be going full time as a scrapper again. And I'll probably have to collect unemployment as well even though I'm sort of against collecting from the tax payers. It'll be **** near impossible to get a job with someone other than SWIFT then. Even though I'm honest and work hard as $hit people would rather hire the lazy lying sack of crap that looks better on paper than hire me.
    Last edited by ScrapmanIndustries; 02-12-2017 at 02:08 PM.


  5. Similar threads on the Scrap Metal Forum

    1. Small scale copper stripper new here
      By timscrapp1621 in forum Introduce yourself
      Replies: 10
      Last Post: 10-29-2016, 11:34 PM
    2. A few small metal items
      By tinman in forum A Day in the Life of a Scrapper
      Replies: 10
      Last Post: 11-23-2013, 01:30 PM
    3. Small pocket scale???
      By Arkansaw in forum Tools and Equipment
      Replies: 14
      Last Post: 01-08-2013, 01:40 PM
    4. need scrap on a small scale
      By Steampunker in forum General - Let's talk business
      Replies: 11
      Last Post: 01-04-2013, 09:46 PM
    5. Small find. Decent metal.
      By tjlock in forum A Day in the Life of a Scrapper
      Replies: 2
      Last Post: 12-19-2010, 08:03 AM

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook