Results 1 to 16 of 16

furnace gas valves

| Dismantling, Breaking Down & Maximizing Scrap
  1. #1
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts

    furnace gas valves

    Does anyone break down furnace gas valves? I've always thrown mine in the dirty aluminum barrell, wondering if it would be worth it to save them for a rainy day. Also, while I was breaking down furnaces tonight I decided to finally tear out the secondary heat exchangers to see just what they are made of. Each one that I did yielded a little over 10 pounds of non-magnetic stainless. You can bet I'm kicking myself for all the stainless I've been throwing away over the last few years!

  2. The Following 4 Users say Thank You for This Post by freonjoe:



  3. #2
    Hypoman's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    Indiana
    Posts
    1,268
    Thanks
    2,772
    Thanked 1,331 Times in 512 Posts
    Do you ever save the thermocouple? A lot of them have platinum wire. Very very small amount....but if you get volume enough????
    Determine never to be idle. No person will have occasion to complain of the want of time who never loses any. It is wonderful how much may be done if we are always doing.
    Thomas Jefferson

  4. The Following User Says Thank You to Hypoman for This Post:


  5. #3
    Ohio Scrapper's Avatar
    SMF Badges of Honor


    Member since
    Jul 2011
    Location
    NW Ohio
    Posts
    336
    Thanks
    467
    Thanked 298 Times in 160 Posts
    I save mine for when I'm low on things to break down. Not sure if it's worth it, but the price is better and it gives me something to do when calls aren't coming in. I do the same thing with transformers too.

    I never knew the secondary heat exchangers were stainless either *facepalm* Learn something new everyday on here!

  6. The Following User Says Thank You to Ohio Scrapper for This Post:


  7. #4
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    I don't get many standing pilot furnaces. Would hot water heater thermocouples be the same?

  8. #5
    Hypoman's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    Indiana
    Posts
    1,268
    Thanks
    2,772
    Thanked 1,331 Times in 512 Posts
    There are several different types of thermocouple setups used in gas furnaces, hot water heaters, and gas stoves.

    I'm gonna start a new thread about these right now Freonjoe!

  9. The Following 5 Users say Thank You for This Post by Hypoman:


  10. #6
    SMF Badges of Honor


    Member since
    Dec 2011
    Posts
    14
    Thanks
    7
    Thanked 14 Times in 6 Posts
    I break my gas valves down. Generally speaking the bottoms usually clean up pretty easy, the tops not so much because of stainless inserts and what not. That being said, all valves are not created equal, YMMV.

  11. #7
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    Cool thread Joe! I started tearing my first one down yesterday, and got about as far as tossing the main valve to the tear down farther pile. I didn't get inside it yet, but am headed that direction. I noticed there are several gaskets around the covers that are no doubt asbestos, and wondered if any of that left showing, could be a problem at the yard ?

  12. #8
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    The ones that I've done have all been a white fiberglass. Some of the older oil burners might have asbestos in the fire box but I'm not sure. My yard has never questioned it.

  13. The Following User Says Thank You to freonjoe for This Post:


  14. #9
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    these were white too, i just expected they were asbestos. It's a full heating unit from an old trailer house

  15. #10
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    I think they stopped using it in the early 70's. If you're in doubt, put it in a trash bag and wait for the hazardous waste day in your neighborhood.

  16. The Following User Says Thank You to freonjoe for This Post:


  17. #11
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    I didn't get to work on it yesterday, but put my magnet around the inside. No stainless there that i could find. I still have one more of these, maybe a little bigger, hoping it'll have some stainless

  18. #12
    freonjoe started this thread.
    SMF Badges of Honor


    Member since
    Nov 2011
    Location
    boise, ID
    Posts
    1,605
    Thanks
    469
    Thanked 1,462 Times in 668 Posts
    Bear, the secondary heat exchangers are used in the high efficiency furnaces. It looks like a stainless car radiator. If the furnace is vented it PVC, chances are it will have one. They sit right under the blower housing so when you pull the blower you can tell right away if it has one or not.

  19. The Following 2 Users say Thank You for This Post by freonjoe:


  20. #13
    SMF Badges of Honor



    Member since
    Feb 2012
    Location
    OK
    Posts
    5,728
    Thanks
    6,814
    Thanked 3,464 Times in 1,989 Posts
    Looks like the only good i got from tearing mine down was the experience ; ) It was from an old trailer house. The internal chamber was heavier metal, but still probly just get shred or tin price here. Was a small motor on the bottom, and a larger blower motor on the top, plus the Al valve I'm yet to dismantle, and a few little fittings

  21. #14
    SMF Badges of Honor

    Member since
    Nov 2018
    Location
    TURKEY
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi we buy thermocouple wires, type s,r and b. Please send me message

  22. #15
    chrenton's Avatar
    SMF Badges of Honor

    Member since
    Feb 2018
    Location
    california
    Posts
    9
    Thanks
    0
    Thanked 4 Times in 2 Posts
    We buy mercury flame sensors found on gas valves of furnaces, boilers, and water heaters.
    Buying Mercury Flame Sensors, $30 each (= $150 lb!) Limited time only!
    White Rodgers brand ONLY. Models 3098-134, 3098-xxx, 3049-xxx, 3094-xxx, (xxx can be any number after dash) 3046-5, 30A46-5.


    Full article at Scrap Metal Forum: https://www.scrapmetalforum.com/scra...#ixzz5tKimtac3



  23. #16
    SMF Badges of Honor

    Member since
    Oct 2020
    Posts
    1
    Thanks
    0
    Thanked 1 Time in 1 Post
    They can be time consuming but once you get a good temper proof screwdriver set, and routine it’s not to bad. Honeywell gives me fits. have yet to find a kit with the right size bit. I use a grinder to notch a slot on those screws, so I can remove them with a flat head. Normally fool with these while watching tv, and it doesn’t seem like work. Time will tell if it’s worth it. Fig I will stack them for a yr. once things pick up I should avg a collection of 10-15 valves a wk. kick myself for not saving them sooner. Some things might seem like to much work, but when saved over the long term can really add up.

  24. The Following User Says Thank You to Krazysride for This Post:



  25. Similar threads on the Scrap Metal Forum

    1. Washing Machine Solenoid Valves
      By Mulden in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 10
      Last Post: 05-20-2020, 10:14 PM
    2. Gas furnace
      By Perrysplace in forum Scrap Metal Tips and Advice
      Replies: 6
      Last Post: 11-18-2012, 05:12 PM
    3. Melting Furnace
      By Copper Head in forum A Day in the Life of a Scrapper
      Replies: 5
      Last Post: 02-16-2012, 10:14 AM
    4. Pressure relief valves
      By Jonniebrass in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 2
      Last Post: 01-17-2012, 10:31 AM
    5. Reversing Valves, ( Heat Pumps )
      By injunjoe in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 0
      Last Post: 10-16-2011, 10:43 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook