I buy and break down mtrs. I pay $0.20lb for the mtrs mostly from my next door neighbor. Here's the numbers and photos of a single 90lb mtr I broke down. This is the single largest mtr I have done. Mike.
90lb @ $0.20 = $18.00
Break down results:
80lb #1 steel @ $0.14 = 11.20
9.28lb #2Cu @ $3.00 = 27.84
$27.84 + 11.20 = $39.04
$39.04 - 18.00 = $21.04
About 1/2 hr to dismantel although I didn't time it.
Last edited by miked; 02-19-2012 at 12:59 PM.
"Profit begins when you buy NOT when you sell." {quote passed down to me from a wise man}
Now go beat the copper out of something, Miked
Nice Mike.I love them motors and the copper even more.I cut my ends off with saw zaw,i have a worry bout the grinder and breathing the dust from the cut.
Kbob, I agree on the dust. I've started working outdoors so much less dust in/on me and my shop. I like using the grinder because its much fater than the sawsall. I had to finish with the sawsall because this motor was too big for the 4 1/2" ginder. Mike.
That's what I'm running into as well. Time to up it to a 7 or 9 I am thinking.Originally Posted by miked
Experienced Scrapper
|
Beautiful, Mike. don't you just love the color of that copper after you cut it. I do it the same way...thanks to you and others who taught me. I always use my grinder....much faster and smoother, but I haven't had one that big yet. Thanks for posting this. It will help the noobs immensely.
|
if you are worried about dust you can buy a respirator with dust cartridges at HomeDepot for like 12 bucks wash it after each use and change out the cartridges every few days
Old dogs care about you even when you make mistakes;
God bless little children while they're still too young to hate
I use an old tablesaw with a 10" cut off blade in it. Was always flexing and breaking the cut off blades when I used my grinder. Great set of pics! Were the end caps aluminum?
Metal Recycling Entrepreneur
Was there still a tag on the motor, or do you know what the HP rating on it was?
No the end caps were steel. And there was a tiny amount of insulated wire not worth weighing. I think the percent of copper was lower on this than on most of the smaller motors I do. Also on many of the smaller motors the end caps are AL as Freonjoe referred to. I have considered using a table saw to cut the coil off. I am wondering what type blade you are using. I would guess a fine tooth plywood type blade.
If I were doing many of these large motors I would buy a bigger angle grinder as IdahoSrapper suggested.
I did it because we have a lot of new members and I find pictures answer a lot of questions. Thanks for looking, Mike.
Mike, I'm using a standard 10" chop saw blade. I get them at Lowes for 4.00 apiece. I can do 40 or 50 windings with each one. And I do use a mask and facw shield.
Out of curiosity is the shell, stator, and outer skin considered prepared steel or tin? I have been throwing it into the tin pile, but had a ephinany err brainfart. Gee I wonder if that is prepared? lol
Last edited by ozzy214; 02-19-2012 at 09:10 PM.
On this one it would be #1 at my yard perhaps prepared at yours. Each seems to have their own standards. And those standards seem to change depending on how badly they need the steel. I am going to put this in a differnt pile than the scrap from computers and the like which is classified #2 at my yard. #1 pays 0.14/lb and #2 is .12/lb. Mike.
Mike, are you supposed to be lifting 90# motors?
|
You can also get a pack of those paper masks for cheap, least they keep the dust out,, DEE!! You don't even want a case of dust pneumonia. Or worse,,,if you are worried about dust you can buy a respirator with dust cartridges at HomeDepot for like 12 bucks wash it after each use and change out the cartridges every few days
P & M Recycling - Specializing in E-Waste Recycling.
If you enjoy your freedom, thank a vet.
scoundrel
Table saw with cut off blade is a great idea! I have an old craftsman table saw that would be perfect for that...
Metal Recycling Entrepreneur
|
I find that for me a chopsaw works best on cutting the wire ends off. So far both cap ends of the motor have been i think cast aluminum. As for cutting the frame i use a plasma cutter at work.
I have sense went to a chop saw myself.Much quicker than my old method with my saw zaw.
There are currently 1 users browsing this thread. (0 members and 1 guests)
|
Browse the Most Recent Threads
On SMF In THIS CATEGORY. 
OR 
|
Posting Permissions
Register To Reply
Bookmarks