Results 1 to 15 of 15

Compressors

| Dismantling, Breaking Down & Maximizing Scrap
  1. #1
    C.M.HUNTER started this thread.
    SMF Badges of Honor

    Member since
    Nov 2010
    Posts
    4
    Thanks
    0
    Thanked 1 Time in 1 Post

    Compressors

    Hello all, I just started scrapping stuff about 6 months ago for extra cash. My Job is for a ice machine and refrigeration distributor. Being so we have to process all warranty for these machine. Before I started taking them they company threw away all the warranty parts after the 90 hold period. I started taking them to scrap for extra cash, I talked to the manager about it, its all good. SO, right now I have about 25 large compressors to scrap. I have already drained them and cut them open. My question is....the casing can recycle as iron #1 I think, and the copper wire is worth pulling out. But has anyone scrap these before and know if there is anything else worth value? I am cutting them open, pulling the motors out then removing the copper winding from the motor. Cut the copper out and throw the rest aside. SO is that it? Just scrap the copper and the rest as mixed? Thanks for advice! Finding this forum to have some good advice for someone that just started.

  2. The Following User Says Thank You to C.M.HUNTER for This Post:



  3. #2
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    Far as I've seen with them, that's it. What are you using to cut them open? Are you sure you're getting a good profit (Return On Investment)? I started cutting an AC compressor with a Sawzall and figured it wasn't worth the time it was taking. How much copper did you get from one compressor?
    People may laugh at me, but that's ok. I laugh all the way to the bank.

  4. #3
    C.M.HUNTER started this thread.
    SMF Badges of Honor

    Member since
    Nov 2010
    Posts
    4
    Thanks
    0
    Thanked 1 Time in 1 Post
    Quote Originally Posted by Mick View Post
    Far as I've seen with them, that's it. What are you using to cut them open? Are you sure you're getting a good profit (Return On Investment)? I started cutting an AC compressor with a Sawzall and figured it wasn't worth the time it was taking. How much copper did you get from one compressor?
    well I get the compressors for free. I use an angle grinder with a metal cutting wheel on it. They cost about $1.50 per wheel and I can scarp about 4-5 compressors with 1. (I have tons a wheels to so thats not an issue. The compressors are very large, I am getting about 4 lbs on average from each compressor from the wiring and some also have copper tubing. takes about 10min per compressor to set it up, cut it open, unscrew the bolts( wish I had a power tool for those **** hex nuts) and get all the copper wire out. So not to bad. thats about 12 from copper alone. plus the casings/motors are pretty **** heavy. Some of the parts inside look like what I think is tin, some iron and some aluminum.

    Edit: These compressors are about 80-100 lbs each. I have some small 30-45 lbs ones.....not sure if those would be worth the time....I have not cut on open yet.
    Last edited by C.M.HUNTER; 11-20-2010 at 08:26 PM. Reason: edit

  5. #4
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    Ok. Yeah, I said Sawzall - meant angle grinder. My compressors are the smaller ones. Those big ones sound like they'd be worth it. The casings should be #1.

  6. #5
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    I have done a few, messy but worth it if you have a lot.
    The windings sometimes have a mix of Copper wire & Ali wire, its easy to see if you cut thru the windings.
    Its a bugger when you find the Ali...... dammit!

    I cut off one end of the motor windings & pull the wire out the other end.
    Theres bits of copper pipe & some brass fitting bits as well.
    I have yet to pull apart a bigger 3 phase one though, that'l be interesting..

  7. #6
    Phithy McNasty's Avatar
    SMF Badges of Honor


    Member since
    Dec 2010
    Location
    NW Arkansas
    Posts
    27
    Thanks
    0
    Thanked 9 Times in 2 Posts
    Most of the compressors I get are smaller ones out of residential heat and air units. I cut one in half once. It did'nt have copper wire. That was the last one I cut. I strip the outside and drill a 1 1/2 inch hole with a holesaw to drain the oil and sell it as a motor.

  8. #7
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    Quote Originally Posted by C.M.HUNTER View Post
    well I get the compressors for free. I use an angle grinder with a metal cutting wheel on it. They cost about $1.50 per wheel and I can scarp about 4-5 compressors with 1. (I have tons a wheels to so thats not an issue. The compressors are very large, I am getting about 4 lbs on average from each compressor from the wiring and some also have copper tubing. takes about 10min per compressor to set it up, cut it open, unscrew the bolts( wish I had a power tool for those **** hex nuts) and get all the copper wire out. So not to bad. thats about 12 from copper alone. plus the casings/motors are pretty **** heavy. Some of the parts inside look like what I think is tin, some iron and some aluminum.

    Edit: These compressors are about 80-100 lbs each. I have some small 30-45 lbs ones.....not sure if those would be worth the time....I have not cut on open yet.
    I have been cutting open the smaller ones, and found if you have the extra time (I strip out the wire when I am sitting on the porch with nothing else to do) they are worth it. I have filled two 5 gallon buckets with the windings (and I mash them down to get as much as possible in each bucket). Question I have is what brand of metal cutting wheel do you use? I have been getting the cheap ones from Harbor Freight (10 for 7.99) and it usually takes a little more than one to cut all the way around the casing. Basically my cost to cut through one is around 80 cents or so each, while it looks like yours is 30 - 40 cents each.

  9. #8
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    Wayne1956, I'd started a thread wondering the same thing. I never got any response, so I went to a lumber store and asked their recommendation for something "worth having". Wound up special ordering two - Turbo brand 7" Pipeline Wheel Type 27 A30R-BF. I think they're also under the brand of "Bulldog". They listed for a little over $6 a piece. I got them for $10+tax. I couldn't find them online so maybe its a "store-only" thing. I haven't used it on anything heavy yet (just aluminum and copper), but seems like they'll do ok.

    I looked at those cheap ones, but I wouldn't waste my money.

  10. #9
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    Quote Originally Posted by Mick View Post
    Wayne1956, I'd started a thread wondering the same thing. I never got any response, so I went to a lumber store and asked their recommendation for something "worth having". Wound up special ordering two - Turbo brand 7" Pipeline Wheel Type 27 A30R-BF. I think they're also under the brand of "Bulldog". They listed for a little over $6 a piece. I got them for $10+tax. I couldn't find them online so maybe its a "store-only" thing. I haven't used it on anything heavy yet (just aluminum and copper), but seems like they'll do ok.

    I looked at those cheap ones, but I wouldn't waste my money.
    I did an experimentation with my angle grinder, and found I was using it wrong. I basically cut throught the shell at one point, then continued the cut all the way around. This is really hard on the wheel. I found I could get twice as much use out of it if I would make a shallow cut all the way around, cut a little more a second time, then cut through and take it all the way around the third time. I was not forcing the wheel to cut all the way through the first time, which made it hard on the wheel and wore it down quickly. Now I can cut about 20 shells with a cheap pack of wheels instead of 8 - 9.

  11. The Following User Says Thank You to wayne1956 for This Post:


  12. #10
    msmoorad's Avatar
    SMF Badges of Honor


    Member since
    Apr 2013
    Location
    Durban, South Africa
    Posts
    689
    Thanks
    713
    Thanked 746 Times in 356 Posts
    just picked up HEAVY compressor today

    i think its easily 100kg's
    about 225lbs

    waiting for a chance to see what goodies lie inside.

  13. #11
    greytruck's Avatar
    SMF Badges of Honor



    Member since
    Jan 2012
    Location
    Thornton, Illinois
    Posts
    1,873
    Thanks
    1,638
    Thanked 1,733 Times in 893 Posts
    Quote Originally Posted by wayne1956 View Post
    I did an experimentation with my angle grinder, and found I was using it wrong. I basically cut throught the shell at one point, then continued the cut all the way around. This is really hard on the wheel. I found I could get twice as much use out of it if I would make a shallow cut all the way around, cut a little more a second time, then cut through and take it all the way around the third time. I was not forcing the wheel to cut all the way through the first time, which made it hard on the wheel and wore it down quickly. Now I can cut about 20 shells with a cheap pack of wheels instead of 8 - 9.
    Exactlly, I figured this out when I did my first one. I realized that trying to cut all the way threw i was cutting to far in and was grinding the motor too. ooops Some times ya gotta learn the hard way.

  14. #12
    sledge's Avatar
    SMF Badges of Honor


    Member since
    Nov 2012
    Location
    Central Indiana
    Posts
    2,717
    Thanks
    4,534
    Thanked 4,240 Times in 1,609 Posts
    My core buyer used to take these whole.. about a month ago I brought 2 in and got the "We don't buy these anymore" I said "How do I rid myself of these now then.." He pointed me to the biggest scrap yard in the area but said- "yeah they have to be cut out and fully drained" Now they just stay in the appliance they are paired with and go in as sheet steel.. Not worth the extreme mess for me to go at it any other way.. Just my .02.

    If anyone in Indiana is willing to drive here to me.. I'd save them up for you if you want to break them down.. I just don't think it will be worth the gas.. but who knows. I don't get hundreds of these, probably 1 or 2 a month.
    Last edited by sledge; 06-12-2013 at 05:04 PM. Reason: Spelling
    I'm so into scrapping.. When my Steel Toe Boots Wear out, I cut the Steel out of them and recycle the Toe!

  15. #13
    SMF Badges of Honor


    Member since
    Jun 2013
    Location
    Toledo, Ohio
    Posts
    550
    Thanks
    551
    Thanked 323 Times in 200 Posts
    There is a piece with aluminum on it called the rotor sell as breakage

  16. #14
    SMF Badges of Honor

    Member since
    Mar 2018
    Location
    houston
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    If you guys are interested in selling your scrap cores I can buy them for more than just scarp. If you want to know home much you can get for each one give me a call and make some real more than just scarp at 210-587-7964 or 832-460-1065 ask for Oscar

  17. #15
    mike1's Avatar
    SMF Badges of Honor


    Member since
    Dec 2011
    Location
    Rochester indiana
    Posts
    550
    Thanks
    231
    Thanked 93 Times in 76 Posts
    i found out if the steel has anykind of aluminum on it its considered breakage and you get .10 a lb instead of .06 lb of steel. so if its got the tiniest bit of ali i count it as breakage.



  18. Similar threads on the Scrap Metal Forum

    1. A/C Compressors
      By poundigity24 in forum Scrap Metal Questions and Answers
      Replies: 14
      Last Post: 05-08-2023, 07:40 PM
    2. National - Refrigerator Compressors
      By Jeviduty in forum Scrap Buyers & Sellers
      Replies: 39
      Last Post: 09-15-2013, 03:37 PM
    3. compressors
      By Copper Head in forum A Day in the Life of a Scrapper
      Replies: 8
      Last Post: 07-09-2012, 08:49 PM
    4. AC compressors
      By Copper Head in forum A Day in the Life of a Scrapper
      Replies: 2
      Last Post: 05-29-2012, 08:12 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook