Results 1 to 8 of 8

Found some clean steel

| A Day in the Life of a Scrapper
  1. #1
    wavecrazed started this thread.
    wavecrazed's Avatar
    SMF Badges of Honor


    Member since
    Oct 2011
    Posts
    219
    Thanks
    13
    Thanked 69 Times in 48 Posts

    Found some clean steel

    Yesterday came up upon a couple of new warehouses being built, probly 60 bay doors with two roll off full of metal framing the were the trimmed pieces. We filled the truck a short bed.Waited till monday till the high paying yards open.


  2. The Following 2 Users say Thank You for This Post by wavecrazed:



  3. #2
    SMF Badges of Honor

    Member since
    Oct 2019
    Location
    NJ
    Posts
    9
    Thanks
    6
    Thanked 6 Times in 6 Posts
    What town are you in? And what do you think you will get a lb?

  4. #3
    auminer's Avatar
    SMF Badges of Honor



    Member since
    Nov 2012
    Location
    Allen, TX
    Posts
    1,233
    Thanks
    579
    Thanked 2,301 Times in 857 Posts
    Better hope that those roll offs weren't there specifically to put those steel pieces in for recycling by the builder.

    Did you as for permission? look around for cameras?

    I get that it's tempting, but you gotta err on the side of not overstepping.
    Out of clutter, find simplicity. --Albert Einstein

  5. The Following 8 Users say Thank You for This Post by auminer:


  6. #4
    wavecrazed started this thread.
    wavecrazed's Avatar
    SMF Badges of Honor


    Member since
    Oct 2011
    Posts
    219
    Thanks
    13
    Thanked 69 Times in 48 Posts
    They are just trash bins no signs. I got 4.50 a 100 lbs
    for the clean steel

  7. #5
    hobo finds's Avatar
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    tucson, az
    Posts
    4,746
    Thanks
    6,035
    Thanked 5,906 Times in 2,555 Posts
    You probably helped them out as price for steel so low it was going to the landfill for a charge.
    Better than the dump!

  8. #6
    SMF Badges of Honor


    Member since
    Jun 2017
    Location
    Las Vegas
    Posts
    1,306
    Thanks
    3,232
    Thanked 1,922 Times in 785 Posts
    At $90/ton a full roll-off is still hundreds of dollars of steel scrap. If you ask you might get it for free still *and* on your schedule as well as make a contact for a regular scrap supply from the demo firm. Pulling scrap uninvited from a roll-off can get you banned from yards if there were cameras and whoever owns the roll-off circulates the pictures

  9. The Following User Says Thank You to JJinLV for This Post:


  10. #7
    SKWrapper's Avatar
    SMF Badges of Honor

    Member since
    Apr 2018
    Location
    Denver, CO
    Posts
    377
    Thanks
    578
    Thanked 404 Times in 203 Posts
    ...I have gotten paid to haul away things instead in lieu of people getting a roll off. I recently made ALOT for ~2 hours of work (my son and I- I'd rather not post the amount) before my truck accident. It made mockery of my hourly rate for my side gig of IT contracting - and needless to say more than collecting any kind of metal or e-waste - but... there was some scrap in those 2 loads as well. If you have a truck, even with very little skill and a small truck you should have some $$$.
    Last edited by SKWrapper; 11-06-2019 at 09:07 PM. Reason: haha spelled "needless" as "needles" + another spelling error

  11. The Following User Says Thank You to SKWrapper for This Post:



  12. Similar threads on the Scrap Metal Forum

    1. Spring steel/couch springs - Worth more than regular steel?
      By Sagan in forum Scrap Metal Questions and Answers
      Replies: 5
      Last Post: 05-30-2015, 01:43 AM
    2. Higer gas prices and steel steel sucks
      By hobo finds in forum A Day in the Life of a Scrapper
      Replies: 7
      Last Post: 05-29-2015, 05:43 PM
    3. As steel prices are down time to prepare steel?
      By hobo finds in forum Scrap Metal Questions and Answers
      Replies: 1
      Last Post: 10-27-2014, 07:37 PM
    4. This thead is a question - stainless steel processing: cut with arc welderand still be considered clean?
      By heeb49 in forum Scrap Metal Questions and Answers
      Replies: 4
      Last Post: 02-14-2014, 11:35 PM
    5. Found a whole truckload of steel in the trash yesterday
      By fiat128 in forum A Day in the Life of a Scrapper
      Replies: 16
      Last Post: 02-20-2013, 06:05 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook