Results 1 to 5 of 5

Stockpiling Bare Bright Copper

| A Day in the Life of a Scrapper
  1. #1
    recyclersteve started this thread.
    SMF Badges of Honor


    Member since
    Apr 2018
    Location
    United States
    Posts
    268
    Thanks
    212
    Thanked 179 Times in 97 Posts

    Stockpiling Bare Bright Copper

    I have one of those 5 gallon buckets that I use to put bare bright copper into. The bucket used to have chlorine tablets for pools in it. Even though I washed it, the bucket still has a bit of a chlorine smell in it. I'd like to wait until the bucket is full before I turn it in. That could be six months to perhaps a couple of years before it happens.

    Is there anything wrong with waiting that long- other than running the risk that the price of copper could go down? I am thinking that the bare bright could oxidize and change color, but will keep it indoors at room temperature instead of exposing it to the elements outside.



    I realize that if the copper is not bright and shiny, it will fetch perhaps 10-15 cents less per pound. I'm willing to take that chance.

    Is there anything else wrong with this strategy?


  2. #2
    Patriot76's Avatar
    SMF Badges of Honor


    Member since
    Dec 2012
    Location
    Buffalo Commons
    Posts
    2,949
    Thanks
    10,589
    Thanked 7,220 Times in 2,256 Posts
    You might be better off finding a better container to store it in. All kinds of containers can be found while out scrapping. As far as stock piling, if you have room why not.
    Give back more to this world than we take.

  3. The Following User Says Thank You to Patriot76 for This Post:


  4. #3
    SKWrapper's Avatar
    SMF Badges of Honor

    Member since
    Apr 2018
    Location
    Denver, CO
    Posts
    377
    Thanks
    578
    Thanked 404 Times in 203 Posts
    Do you not scrap appliances? Do you have a wire stripper?

    I ask because it shouldn't take very long to fill up a 5 gallon bucket with copper if you scavenge from appliances etc... I don't strip every wire but I do save almost all of the wire and strip only the big ones - ex. stove wire.
    Last edited by SKWrapper; 07-26-2018 at 11:47 AM.

  5. #4
    Stargate1's Avatar
    SMF Badges of Honor

    Member since
    Aug 2016
    Location
    Loganville, GA
    Posts
    148
    Thanks
    24
    Thanked 116 Times in 59 Posts
    Same here. I strip all the wire of a certain gauge that looks as if it is worth the time. Most of the time it is THHN wire and other stuff like dryer wire, stove wire, thick extension cords, etc. I can fill a five-gallon bucket in a couple weeks if I get a fair amount of the wire. Unfortunately, I don't very often. But, I did just pick up 20 buckets that contained a polishing solution for the type of tile you see in schools. My old high school polished up this summer, and I was able to walk out with 20 buckets plus lids. A nice pickup. On that note, you should be able to find a bunch of cleaner (as in not filled with chemical smells and liquids) pretty easily. Just dumpster dive behind some businesses or hardware stores. Even Lowe's and HD might have something in the dumpster. I have found stuff there before.

  6. The Following User Says Thank You to Stargate1 for This Post:


  7. #5
    recyclersteve started this thread.
    SMF Badges of Honor


    Member since
    Apr 2018
    Location
    United States
    Posts
    268
    Thanks
    212
    Thanked 179 Times in 97 Posts
    I don't do much with appliances as I don't have a truck. I may snip wires off some of them, but much of the wire I get is not worth stripping. I get a lot of that small soft 30% type wire- I get about the same and sometimes more by leaving it insulated. I do like to strip ROMEX and some types of THNN/THWN wire. The stripper I have is manual and made by TNT Tooling- it is ok, but not as good as what I was expecting from looking at the Youtube videos (like MooseScrapper's) before I bought it. For instance, on some of the THNN wire there is a clear plastic coating of insulation on top of the other insulation. Sometimes that plastic is quite difficult to remove and then you have to strip the wire again to remove the other layer of insulation. Sometimes it is so hard to remove that I stop trying and sell it as insulated.


  8. Similar threads on the Scrap Metal Forum

    1. bare bright
      By hunterandscrapper in forum Scrap Metal Prices
      Replies: 10
      Last Post: 07-17-2014, 06:16 AM
    2. romex stripped to becoem bare and bright?
      By exibar in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 5
      Last Post: 11-01-2012, 06:34 AM
    3. what determines when copper is bare bright and not?
      By bluemeate in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 15
      Last Post: 09-28-2012, 05:35 PM
    4. Questions about Rotors , Stators , and Bare Bright
      By Bear in forum Scrap Metal Questions and Answers
      Replies: 11
      Last Post: 06-22-2012, 12:31 AM
    5. bare bright copper question
      By scrapmonkey in forum Scrap Metal Questions and Answers
      Replies: 7
      Last Post: 01-24-2012, 07:36 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook