Results 1 to 2 of 2

Can my dead Lead Acid batteries be reused?

| Batteries, Capacitors, Heat Sinks
  1. #1
    suzy started this thread.
    SMF Badges of Honor

    Member since
    Jan 2017
    Location
    Flat 08,4/F Shing Yip Ind Bldg,19-21 Shi
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Can my dead Lead Acid batteries be reused?

    I have two 12V 4.5Ah sealed Lead Acid batteries from an old electric scooter. The scooter is a decade old, and packed up a few months after purchase. The batteries were literally left as is for almost ten years, and I am unsure if they were connected to the circuit or not during that time.
    Okay, so the one measures 1.1V, and the other -0.6V! The negative voltage is very odd as the batteries were in series and I can't think how that could be physically possible through (dis)charge..
    I do not have any desulphation equipment or similar, all I have is an alarm "UPS box", which slowly charges SLA batteries, although it never gets them above 13.4V as that is what it outputs when no battery is connected, also it's all linear - nothing fancy.
    Is there anything I can do to resurrect these batteries with the equipment I have, or should I just have them recycled? I have a fair amount of knowledge in electronics if there's anything I could do. Also, are there any dangers hooking it up to my charger or hooking up one with a voltage too low in general?



  2. #2
    SMF Badges of Honor



    Member since
    Apr 2015
    Posts
    2,072
    Thanks
    615
    Thanked 2,445 Times in 1,092 Posts
    Quote Originally Posted by suzy View Post
    I have two 12V 4.5Ah sealed Lead Acid batteries from an old electric scooter. The scooter is a decade old, and packed up a few months after purchase. The batteries were literally left as is for almost ten years, and I am unsure if they were connected to the circuit or not during that time.
    Okay, so the one measures 1.1V, and the other -0.6V! The negative voltage is very odd as the batteries were in series and I can't think how that could be physically possible through (dis)charge..
    I do not have any desulphation equipment or similar, all I have is an alarm "UPS box", which slowly charges SLA batteries, although it never gets them above 13.4V as that is what it outputs when no battery is connected, also it's all linear - nothing fancy.
    Is there anything I can do to resurrect these batteries with the equipment I have, or should I just have them recycled? I have a fair amount of knowledge in electronics if there's anything I could do. Also, are there any dangers hooking it up to my charger or hooking up one with a voltage too low in general?
    Sealed lead acid battery's ten years old with plenty of repetitive charging at some point the cells became low on water the exposed plates became sulfated, if you can prise the caps off then refill each cell with deionized or distilled water just until the water reaches a ring located about an inch below the top of the battery case after the cap has been removed this becomes visible.

    Once you've added water, wait half an hour, some of that water is going to soak into those dry plates, check and add water repeating the wait time once again.

    Some caps from sealed battery's are press fitted while others are glued on.

    There are additives on the market used to rejuvenate a battery, I've never used any of these products, so I'm unable to give any pro's or con's of there use.

    Now that your satisfied no more water is needed you can hook up a charger, hopefully the battery will take a charge but in my opinion a ten year olf battery has a one way trip to the scrap yard.

    Older commercial battery charges were equipped with a feature that would de-sulphate a battery's plates.

    Other factors with an aged battery, if you were to disassemble the battery you would find that a fiber glass mat separates each lead plate, in the old days this separator was made from a thin layer of wood. The below the plates built into the case is a sump, this sump is to allow for crap that sheds free from the plates to have a place to settle with out short circuiting plates in the cell above.

    Shedding of plate material comes with age and rough usage from driving over rough gravel roads shaking the battery, this is one of two reasons the battery is secured in place the other is to secure it in case of a vehicle roll over to keep the top posts from shorting out causing a fire. Today most vehicles I would think use a side post battery,

    In my line of work any battery that went dead was in a machine no easily accessible and had to be packed out for charging by swapping with my truck battery, now the funny thing is that an alternator will not charge a fully discharged battery while a a generator will.

    My first car a 1947 Hudson always had a dead battery, because it had a generator the car could be push started even with out a battery installed.

  3. The Following User Says Thank You to alloy2 for This Post:



  4. Similar threads on the Scrap Metal Forum

    1. This thead is a question - Lead-acid batteries
      By nutpie in forum A Day in the Life of a Scrapper
      Replies: 19
      Last Post: 10-13-2015, 06:55 PM
    2. Lead Acid Batteries
      By Ewasted in forum General - Let's talk business
      Replies: 20
      Last Post: 03-31-2014, 11:22 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook