Results 1 to 15 of 15

Cutting torch Recommendations?

| Tools and Equipment
  1. #1
    Meadowview started this thread.
    SMF Badges of Honor


    Member since
    Oct 2010
    Posts
    24
    Thanks
    6
    Thanked 6 Times in 3 Posts

    Question Cutting torch Recommendations?

    I am shopping for a cutting torch set up and wonder if anyone has any recommendations as to what to buy. The equipment seems to be quite expensive and I don't want to spend more than necessary. Here is my situation:
    • I have a Ford F350 with a utility body and want to put the torch and tanks inside a cabinet which has a door opening height of 36" and 42" height inside.
    • I need to buy a cutting torch to scrap some farm equipment and a forklift.
    • I would also like to have the flexibility to do different kinds of small jobs for myself such as welding and heating as the need arises but cutting is the primary concern today.


    Here are my questions:
    • How much should I plan to spend to get a decent setup?
    • Is buying used equipment a bad idea or do the torches hold up well?
    • Since I have nothing at this point, should I buy a starter kit?
    • Is buying a well known name brand such as Victor important?
    • Which fuel, acetylene or propane?
    • If propane is the way to go, should I buy an acetylene starter kit and then swap out the regulator?
    • What size cutting tips should I have in my tool box?
    • Torches seem to come in light, medium and heavy duty. Do I need to buy the heavy duty equipment?
    • I am concerned about starting fires in dry farm fields. Any thoughts?
    • Any other recommendations?


    Thanks so much for your help!

  2. The Following User Says Thank You to Meadowview for This Post:



  3. #2
    708bigbuck's Avatar
    SMF Badges of Honor


    Member since
    Aug 2010
    Posts
    53
    Thanks
    0
    Thanked 26 Times in 14 Posts
    I know I always find decent setups at the flea market by my house. You can check Harbor Freight or Northern tool. They have fairly decent sets for resonable prices.( alot better price than you will find at a welding house.) Just remember if you are going to be doing alot of cutting, you will burn through oxygen very quickly and that can eat up your profits pretty fast. Hope this helps a little. Good luck.

  4. #3
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    I don't know if this would work for you, but I considered buying a cutting torch and decided to use a heavy duty angle grinder instead. I've found I can cut through almost anything with a bonus - telling stainless steel from aluminum. Aluminum doesn't throw sparks - stainless steel does. I don't worry about cutting through something and setting what's inside on fire (like wiring or oil in compressors).
    People may laugh at me, but that's ok. I laugh all the way to the bank.

  5. The Following User Says Thank You to Mick for This Post:


  6. #4
    Meadowview started this thread.
    SMF Badges of Honor


    Member since
    Oct 2010
    Posts
    24
    Thanks
    6
    Thanked 6 Times in 3 Posts
    I thought I would follow up on this. I bought a torch setup and wish I hadn't. It takes too long to setup, I spend way too much on gas and oxygen, I don't feel comfortable using it, it is slower than I envisioned, it takes a lot of time to go to the supply house for fresh tanks, the tanks take up valuable space on my truck, and there are not very many situations away from home where I feel I can use it safely. Also as I feared, I am constantly stamping out fires when I do use it.

    I know a lot of the problems stem from my lack of experience but all in all I wish I had put the money into something else.

    Thanks to Mick and Bigbuck for your earlier input. I appreciate it!

  7. #5
    SMF Badges of Honor



    Member since
    Jan 2011
    Posts
    1,159
    Thanks
    0
    Thanked 248 Times in 169 Posts
    Man just use them you will get them down.I take it you didnt buy propane?



    There is some bad ass torches on the internet i would love to buy but they are 1500+ They run off of gasoline.

  8. #6
    SMF Badges of Honor


    Member since
    Feb 2011
    Location
    S.E. Missouri
    Posts
    21
    Thanks
    2
    Thanked 3 Times in 2 Posts
    I've seen the gasoline torch's on web videos they are fast but I don't have the stones to mix gas and fire.
    Focker do you use propane and if you do is it enough of a saving to buy a $70 regulator?

  9. #7
    SMF Badges of Honor



    Member since
    Jan 2011
    Posts
    1,159
    Thanks
    0
    Thanked 248 Times in 169 Posts
    propane will save you a ton.you can get a propane tank filled for 30 and ace would be 80 plus so propane is the way to go.

  10. #8
    SMF Badges of Honor

    Member since
    May 2013
    Location
    41219
    Posts
    2
    Thanks
    0
    Thanked 1 Time in 1 Post
    a harris torch and #6 tips bout the best way to go small light and cutting would be fast to make your money out of a tank that what i would use most people use a #4 but i know that only slows you down but it up to you if you want to play whit the metal or cut it to make money

  11. #9
    jghilino's Avatar
    SMF Badges of Honor

    Buying Specialty Escrap of all kinds, resale grade computer parts

    Member since
    Sep 2012
    Location
    KANSAS CITY
    Posts
    2,672
    Thanks
    1,429
    Thanked 1,453 Times in 919 Posts
    a no 1 tip is about the largest you should need based on what your talking about, i dont know what your talking about with the no 6 and no 4 tips, you scrapping out a m1a1? With the proper tip size and regulator settings you can get alot out of a bottle of oxygen.

    I would use the #0 tip. The kerf on your cut will be much smaller. On my Victor regulators I run my Acetylene at 7lbs. and my Oxygen at 20lbs.
    I buy and sell all types of scrap and escrap. I buy specialty and hard to sell escrap. I buy resale items. PM me or contact me at jghilino@hotmail.com
    I AM ACTIVELY BUYING ESCRAP OF ALL TYPES. BOARDS, RAM, CPUS AND MUCH MORE

  12. #10
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    Harris is the only way to go. you can buy a full set w/tanks often on CL. for around $150 they are a handy tool to have around if you have the extra bucks. get the small 100 lb oxygen tank and propaine not only is cheeper but I think it cuts better once you learn how to use it, just my .02
    "anyone who thinks scrappin is easy money ain't doin it right!"

  13. #11
    Re-cycler is offline Metal Recycling Entrepreneur
    Re-cycler's Avatar
    SMF Badges of Honor

    Member since
    Jun 2011
    Location
    Southwest MN
    Posts
    167
    Thanks
    126
    Thanked 207 Times in 114 Posts
    I've been using my little Smith torch for 35+ years with no real problems for a few years I was cutting at least 50 tons of steel a year.
    My regulators (brooklyn I think) are so old I had to buy an adapter for the gas one to adapt to modern female gas/propane/acetylene tanks.
    They still have the original beveled glass lenses in them.
    You do not need a special regulator for different gasses just the cutting tips are different.
    Propane tips for my Smith are only about $15.oo I just picked up another complete Smith rig for twenty bucks from a friend who had 3 sets and it is like new guages and all.
    I pay $50. to fill a 100 lb tank of propane and that will probably last through 10 to twenty full size tanks of oxygen at about $26 per tank......I own my tanks even though I just exchange them.
    My paper work is worth the current cost of new tanks.

  14. #12
    Re-cycler is offline Metal Recycling Entrepreneur
    Re-cycler's Avatar
    SMF Badges of Honor

    Member since
    Jun 2011
    Location
    Southwest MN
    Posts
    167
    Thanks
    126
    Thanked 207 Times in 114 Posts
    This is my newest friend $375. and 100 mile one way drive to pick it up just have to get my 3-phase plugin wired out and I'll be havin some fun with stainless aluminum and anything else I want to play with I have 2 tons of 1/4 in plates to play with.

  15. The Following 2 Users say Thank You for This Post by Re-cycler:


  16. #13
    SMF Badges of Honor

    Member since
    Jul 2013
    Posts
    7
    Thanks
    0
    Thanked 1 Time in 1 Post
    Torches are great for heavy steel not for cars or light gauge. I use a demo saw or grinder for that stuff. Also I'm not so sure you can put the tanks in an enclosed space. I'm pretty sure they have to be secured in an open area.

  17. #14
    SMF Badges of Honor




    Member since
    Mar 2012
    Location
    ks
    Posts
    2,187
    Thanks
    2,513
    Thanked 2,140 Times in 898 Posts
    Quote Originally Posted by Focker View Post
    propane will save you a ton.you can get a propane tank filled for 30 and ace would be 80 plus so propane is the way to go.
    Propane can't weld properly! Accetylene is the only fuel that you can weld with it. And yes propane is cheaper, but not two ways about it propane requires a bunch more oxygen than Acctyelene, so where exactly is the savings ?

    And per brand, You won't see me Strike up a torch that doesn't say victor on it! Not a Chinese made knock off "victor style" but an actual victor brand torch
    Alvord iron and salvage
    3rd generation scrapper and dam proud of it

  18. #15
    SMF Badges of Honor




    Member since
    Mar 2012
    Location
    ks
    Posts
    2,187
    Thanks
    2,513
    Thanked 2,140 Times in 898 Posts
    Quote Originally Posted by Meadowview View Post
    I thought I would follow up on this. I bought a torch setup and wish I hadn't. It takes too long to setup, I spend way too much on gas and oxygen, I don't feel comfortable using it, it is slower than I envisioned, it takes a lot of time to go to the supply house for fresh tanks, the tanks take up valuable space on my truck, and there are not very many situations away from home where I feel I can use it safely. Also as I feared, I am constantly stamping out fires when I do use it.

    I know a lot of the problems stem from my lack of experience but all in all I wish I had put the money into something else.

    Thanks to Mick and Bigbuck for your earlier input. I appreciate it!
    Formal training helps a ton, pun intended. And also a class a fire extinsher is a must too. I bought my used for 100$, and all it needs to be recharged is tap water and 100 psi of compressed air.

    Water Fire Extinguishers by KIDDE - Fire Extinguishers by Zoro Tools Industrial Supplies

  19. The Following User Says Thank You to taterjuice for This Post:



  20. Similar threads on the Scrap Metal Forum

    1. cutting torch
      By decjr2006 in forum Tools and Equipment
      Replies: 13
      Last Post: 11-26-2011, 01:15 AM
    2. Cutting tool that isn"t a torch
      By sdw in forum Tools and Equipment
      Replies: 5
      Last Post: 07-13-2011, 02:54 PM
    3. Looking for recommendations for a cutting wheel
      By Mick in forum Tools and Equipment
      Replies: 1
      Last Post: 12-05-2010, 10:46 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook