Page 1 of 2 12 LastLast
Results 1 to 20 of 21

air conditioner radiators

| Scrap Metal Tips and Advice
  1. #1
    Mstra started this thread.
    SMF Badges of Honor


    Member since
    Apr 2012
    Posts
    15
    Thanks
    4
    Thanked 1 Time in 1 Post

    air conditioner radiators

    Anyone know if theres a way to get the copper piping out of air condition radiators?



  2. #2
    SMF Badges of Honor


    Member since
    Mar 2012
    Location
    new jersey
    Posts
    65
    Thanks
    0
    Thanked 17 Times in 13 Posts
    That might b more work than its worth.

  3. #3
    Mstra started this thread.
    SMF Badges of Honor


    Member since
    Apr 2012
    Posts
    15
    Thanks
    4
    Thanked 1 Time in 1 Post
    Just a shhame u donnt gget jack for them and all that copperr is just sittinng in there

  4. #4
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    I use two methods - depending on how I feel:

    1. Utility (box) knife - Cut along the copper piping or to the side. The aluminum actually cuts pretty easily.

    2. Grinder - run along the copper piping with a grinder. This seems to take longer than the knife, but less effort.
    People may laugh at me, but that's ok. I laugh all the way to the bank.

  5. The Following 3 Users say Thank You for This Post by Mick:


  6. #5
    Hypoman's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    Indiana
    Posts
    1,268
    Thanks
    2,772
    Thanked 1,331 Times in 512 Posts
    Mstra, are you cleaning them before you take them in, what I mean is, are you cutting the steel edges off? You get significantly more if you do that.
    Determine never to be idle. No person will have occasion to complain of the want of time who never loses any. It is wonderful how much may be done if we are always doing.
    Thomas Jefferson

  7. The Following User Says Thank You to Hypoman for This Post:


  8. #6
    SMF Badges of Honor

    Member since
    Dec 2011
    Location
    SC
    Posts
    73
    Thanks
    42
    Thanked 68 Times in 29 Posts
    What is the copper ratio in an AC radiator ?

  9. #7

  10. The Following 2 Users say Thank You for This Post by admin:


  11. #8
    Mstra started this thread.
    SMF Badges of Honor


    Member since
    Apr 2012
    Posts
    15
    Thanks
    4
    Thanked 1 Time in 1 Post
    ok i found a way to get them out its not to hard but way to time consuming, i didnt know that just taking the steel ends off get you more i think ill stick with that thanks

  12. #9
    DESCRAPPER's Avatar
    SMF Badges of Honor


    Member since
    May 2012
    Location
    Banks Alabama
    Posts
    39
    Thanks
    24
    Thanked 13 Times in 9 Posts
    you can cut the copper loops off the ends first then the metal plates. the copper loops add up

  13. #10
    happyscraper's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Location
    spring hill,fl
    Posts
    2,864
    Thanks
    350
    Thanked 1,371 Times in 847 Posts
    The yard I use pays 1.40lbs clean and 1.30lbs dirty. I do like Descrapper said cut the loops off with a metal cut off blade right along the steel then pull the steel off with a pair of chanel locks.

  14. The Following User Says Thank You to happyscraper for This Post:


  15. #11
    BRASSCATCHER's Avatar
    SMF Badges of Honor


    Member since
    Feb 2012
    Posts
    2,476
    Thanks
    3,436
    Thanked 3,965 Times in 1,383 Posts
    If you have a bench vice,stand it in the vice nice and tight, don't worry about crimping the alu. Take channel locks or vice grips, grab the top part of the fin and roll it down around the tool and peel it right off. You can also put it in the vice take a mallet and chisel and pound it off, either gets the job done.
    I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them.” John Wayne-- The Shootist

    NEWBS READ THIS THREAD ABOUT REFINING!!!!
    http://www.scrapmetalforum.com/off-t...ning-read.html

  16. #12
    newattitude's Avatar
    SMF Badges of Honor


    Member since
    Jun 2011
    Location
    Hinckley Ohio, home of the buzzards
    Posts
    2,163
    Thanks
    1,431
    Thanked 2,497 Times in 904 Posts
    I used to take those apart, not any more. A utility knife is OK but its still takes me longer than i want to spend on working on them. Especially if they are the real small piping ones, I figure the copper is so lightweight I do ok turning them in as is - cleaned of course.

  17. #13
    SMF Badges of Honor

    Member since
    Jun 2012
    Posts
    6
    Thanks
    0
    Thanked 1 Time in 1 Post
    Quote Originally Posted by copperhound View Post
    That might b more work than its worth.
    After watching people do this myself. I agree 1,000%.

  18. #14
    SMF Badges of Honor


    Member since
    Jun 2012
    Location
    missouri
    Posts
    39
    Thanks
    0
    Thanked 20 Times in 10 Posts
    this is how I used to do it. Keep in mind I am an amateur scrapper & had to figure it out on my own. It was very labor intensive.

    I did it a bit @ss-backwards though. I would put it in a vice, cut down the inside of the steel sides thru the copper pipes to remove the copper ends (like I said.. I did this the idiot way instead of the smarter way... to cut the copper tube ends off on the outside of the steel sides, then yank or bend the steel sides off), then I would take a box cutter & cut down the sides of the copper tubes though the aluminum..... then i took a steel rod & put it in the tops of the copper tubes & pull them thru the aluminum fins. Like I said... very labor intensive. Anymore I just refuse to do that. I now cut the copper tube ends off, remove the steel ends & then turn in the radiator with the copper tubes still inside the fins. If I had the guts to use cutting tools I would use them to cut the tubes out of the aluminum fins.
    Last edited by dirtymoney; 06-10-2012 at 09:06 AM.

  19. #15
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    Air cons in cars? Normally they are ali, a big box of ali, 2Lb or 1 Kg.

  20. #16
    SMF Badges of Honor


    Member since
    Oct 2011
    Location
    Canada
    Posts
    169
    Thanks
    29
    Thanked 72 Times in 40 Posts
    I think they are referring to this A/C (household not automotive)



    Although I have seen a few actual automotive A/C rads that were CO/AL, rare though

  21. The Following User Says Thank You to myekem for This Post:


  22. #17
    SMF Badges of Honor


    Member since
    Jan 2012
    Location
    Indiana
    Posts
    84
    Thanks
    37
    Thanked 61 Times in 33 Posts
    Myekem.....that pic is priceless! Almost spit my drink everywhere.

  23. The Following User Says Thank You to 12oclock for This Post:


  24. #18
    SMF Badges of Honor


    Member since
    Oct 2011
    Location
    Canada
    Posts
    169
    Thanks
    29
    Thanked 72 Times in 40 Posts
    lol.. Don't get the wrong idea lol, It's not mine. Funny Though.

  25. #19
    THEDANIMAL's Avatar
    SMF Badges of Honor


    Member since
    Oct 2014
    Location
    scranton, pa
    Posts
    29
    Thanks
    0
    Thanked 17 Times in 11 Posts
    i havent found the exact ratio between copper and aluminum but i dont think it take that much time. i use a linoleum knife to make one slice on the copper tube. then i use a long pry bar and pull it between the slice marks and they seem to open up nice. the copper tube usually slides out easy and the linoleum knife lasts alot longer then a utility knife blade. ive done probable 20 ac units worth of radiators and it still has the same results.

  26. #20
    DevinThaScrapper's Avatar
    SMF Badges of Honor

    Member since
    Nov 2012
    Location
    Nebraska
    Posts
    588
    Thanks
    120
    Thanked 605 Times in 247 Posts
    I take a hammer or a sawzall depending on if I'm too lazy to get it out and take the claw of the hammer and hit it between the steel and elbows, and the aluminum rads and peel it back and keep repeating until all the rivets are out. If not I just run my sawzall down it and it's done


  27. Similar threads on the Scrap Metal Forum

    1. Industrial air conditioner need help
      By Chadcam in forum Scrap Metal Questions and Answers
      Replies: 10
      Last Post: 11-26-2015, 12:49 AM
    2. Air Conditioner Value
      By nyjetsfanx93 in forum Scrap Metal Questions and Answers
      Replies: 17
      Last Post: 09-22-2015, 01:25 PM
    3. taking apart air conditioner compressors
      By copycat in forum Scrap Metal Questions and Answers
      Replies: 14
      Last Post: 09-20-2012, 07:58 AM
    4. Scrapping an air conditioner
      By jackshmuc in forum Scrap Metal Videos
      Replies: 1
      Last Post: 07-17-2012, 01:11 AM
    5. Industrial air conditioner need help
      By Chadcam in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 1
      Last Post: 09-20-2011, 03:51 PM

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook