Page 1 of 2 12 LastLast
Results 1 to 20 of 35

electronic ballast?

| Scrap Metal Tips and Advice
  1. #1
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts

    electronic ballast?

    I'm breaking down some light fixtures that I got from a supermarket remodel and I found these long rectangular boxes in them connected to the wires, the boxes are marked "electronic ballast". Would these be considered motors? Should I break them open for copper or try to sell them whole? Should I leave wires connected to them? Thanks for any advice in advance. Sorry I don't have a photograph.

    Success consists of going from failure to failure without a loss of enthusiasm...... Churchill


  2. #2
    SMF Badges of Honor


    Member since
    Apr 2011
    Posts
    75
    Thanks
    2
    Thanked 14 Times in 11 Posts
    Shred.

    They won't take them any other way.
    Everyone one of you is 2 minutes too late.

  3. The Following User Says Thank You to WeWillPrevail for This Post:


  4. #3
    Midnight's Avatar
    SMF Badges of Honor


    Member since
    Oct 2011
    Location
    McHenry County, IL, USA
    Posts
    242
    Thanks
    41
    Thanked 153 Times in 79 Posts
    There does appear to be a market for them if you can find a buyer and have the quantity. Appears to be about half the price of small copper transformers.

    Scrap Times: Copper Ballasts

    Alibaba.com

  5. The Following User Says Thank You to Midnight for This Post:


  6. #4
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    Theres about 100 gms (2/9ths of a Lb?) Copper wire in each one.

    If you want to get dirty you can get better money from them by stripping them.

    What sort? Old, encased in tar.
    Or Modern, covered in white paint?

  7. #5
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    From the mess all over me, I'd say tar. I'm so glad I did laundry today. It's all so covered with hard and soft black stuff that it's hard to see what things are in it.

    Thanks for the info, I'm not sure I want to open up a batch of these.

    do they have tantalum or whatever that stuff is in them, do you know?
    Last edited by Scrapette; 11-20-2011 at 10:37 PM.

  8. #6
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by Midnight View Post
    There does appear to be a market for them if you can find a buyer and have the quantity. Appears to be about half the price of small copper transformers.

    Scrap Times: Copper Ballasts

    Alibaba.com
    Thanks for the links and the other information. I have around sixteen now, but can possible get more, but not a huge number.

  9. #7
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by eesakiwi View Post
    Theres about 100 gms (2/9ths of a Lb?) Copper wire in each one.

    If you want to get dirty you can get better money from them by stripping them.

    What sort? Old, encased in tar.
    Or Modern, covered in white paint?
    Is the copper the wire wrapped around a spool inside a metal frame? How do you get to it? Hammer time?

  10. #8
    eesakiwi's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    NZ
    Posts
    2,531
    Thanks
    2,909
    Thanked 2,556 Times in 1,227 Posts
    The modern ones I pull the backing plate off & use a cold chisle down thru the groove, & then lever the 'C's off with a flat screwdriver, then punch out the squares inside the coil.
    The coils covered in paint so I bash it & most of the paint falls off & they sell as domestic copper.

    The older ones, tar filled,
    I bash the outer case off or heat it in a fire so the tar softens. Then heat the tar off, then pull the iron core - a long legged 'U' shape out of the coil, the coils covered in tar but cleans up easy like.

    Theres other sorts, I have found 3 sorts, but they seem to be just variations of the two.

    About 100gms per ballast, the last tar filled ones had a wooden block in one end to fill up space.
    And a very thin tar soaked ricepaper inside the coil, when I unravelled the wire the ricepaper fell off, made a huge mess of the place & there wasn't much ricepaper, in volume, after all.

    If you think its worth doing, just pull one apart & learn from it & do the rest 'production style'.
    Its a dirty job, but I like to get every little bit possible.

    I have found the wire in the newer ones is a solid single strand, I don't see that very often.
    Last edited by eesakiwi; 11-20-2011 at 11:26 PM.

  11. The Following User Says Thank You to eesakiwi for This Post:


  12. #9
    SMF Badges of Honor



    Member since
    Aug 2011
    Posts
    224
    Thanks
    27
    Thanked 224 Times in 66 Posts
    Hmmm. I would be careful here. I don't have much experience with them but I thought they were considered hazardous. Here's a little clip from this web site on them. Just make sure you aren't poisoning yourself and your family for a few bucks.

    "PCB-containing wet ballasts must be handled as hazardous waste. PCBs were banned from use in fluorescent light ballasts in 1978, but many of these older units may still exist and be in use today since their useful life span is typically 10 to 30 years. Ballasts manufactured after 1978 will be labeled “non-PCB” or “contains no PCBs.” If it doesn’t have either of these labels, it should be assumed to contain PCBs and be handled as hazardous waste."

    http://earth911.com/news/2007/06/16/...lamp-ballasts/

  13. #10
    Filthy's Avatar
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Northern New Jersey
    Posts
    780
    Thanks
    850
    Thanked 372 Times in 202 Posts
    there is a sign at my yard saying the things they dont take. ballast is marked on there clear as day....

    BUT, when i asked the guy who grades my material as i dump it, he told me they take it no problem and that it goes in the shred. whats a guy supposed to think of that? i'm not sure either, but i have about 5 of them in the trunk of my car and they dont really need to move, as i have my hands full with plenty of other scrap right now.
    We're the renegades of Junk!

  14. The Following User Says Thank You to Filthy for This Post:


  15. #11
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by eesakiwi View Post
    The modern ones I pull the backing plate off & use a cold chisle down thru the groove, & then lever the 'C's off with a flat screwdriver, then punch out the squares inside the coil.
    The coils covered in paint so I bash it & most of the paint falls off & they sell as domestic copper.

    The older ones, tar filled,
    I bash the outer case off or heat it in a fire so the tar softens. Then heat the tar off, then pull the iron core - a long legged 'U' shape out of the coil, the coils covered in tar but cleans up easy like.

    Theres other sorts, I have found 3 sorts, but they seem to be just variations of the two.

    About 100gms per ballast, the last tar filled ones had a wooden block in one end to fill up space.
    And a very thin tar soaked ricepaper inside the coil, when I unravelled the wire the ricepaper fell off, made a huge mess of the place & there wasn't much ricepaper, in volume, after all.

    If you think its worth doing, just pull one apart & learn from it & do the rest 'production style'.
    Its a dirty job, but I like to get every little bit possible.

    I have found the wire in the newer ones is a solid single strand, I don't see that very often.
    Thanks for that information, eesakiwi. Since the only yard around here that takes steel won't take them,I may eventually break them down. These have a board in them.

  16. #12
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by wdaddy View Post
    Hmmm. I would be careful here. I don't have much experience with them but I thought they were considered hazardous. Here's a little clip from this web site on them. Just make sure you aren't poisoning yourself and your family for a few bucks.

    "PCB-containing wet ballasts must be handled as hazardous waste. PCBs were banned from use in fluorescent light ballasts in 1978, but many of these older units may still exist and be in use today since their useful life span is typically 10 to 30 years. Ballasts manufactured after 1978 will be labeled “non-PCB” or “contains no PCBs.” If it doesn’t have either of these labels, it should be assumed to contain PCBs and be handled as hazardous waste."

    http://earth911.com/news/2007/06/16/...lamp-ballasts/
    Thanks for for that information, wdaddy, these are marked that they don't contain pcbs. Of course, they could have other nasty stuff in them and they have a lot of tar !

  17. #13
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by Filthy View Post
    there is a sign at my yard saying the things they dont take. ballast is marked on there clear as day....

    BUT, when i asked the guy who grades my material as i dump it, he told me they take it no problem and that it goes in the shred. whats a guy supposed to think of that? i'm not sure either, but i have about 5 of them in the trunk of my car and they dont really need to move, as i have my hands full with plenty of other scrap right now.
    My yard won't take them and mine are marked as having no pcbs. They have boards in them so I may break them down eventually after I figure out a way to do it that doesn't make such a mess. Thanks for the post.

  18. #14
    Scrap man's Avatar
    SMF Badges of Honor

    Member since
    Nov 2010
    Location
    NY
    Posts
    657
    Thanks
    36
    Thanked 172 Times in 93 Posts
    The old ones with tar are major carcinogens (cancer-causing). Not sure about the new ones though. I wouldn't even handle them extensively, much less break them down
    There's nothing more fun and more effective than hitting something repeatedly with a sledgehammer

  19. The Following User Says Thank You to Scrap man for This Post:


  20. #15
    Midnight's Avatar
    SMF Badges of Honor


    Member since
    Oct 2011
    Location
    McHenry County, IL, USA
    Posts
    242
    Thanks
    41
    Thanked 153 Times in 79 Posts
    Find a buyer and let them deal with them is what I say. Some things are just best left to the professionals.

  21. The Following User Says Thank You to Midnight for This Post:


  22. #16
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by Scrap man View Post
    The old ones with tar are major carcinogens (cancer-causing). Not sure about the new ones though. I wouldn't even handle them extensively, much less break them down
    Thanks for that information. These are from 1995 0r 1997.

  23. #17
    SMF Badges of Honor

    Member since
    Jul 2011
    Location
    Usa
    Posts
    763
    Thanks
    67
    Thanked 312 Times in 179 Posts
    I dotn know about anyone else, but they go in my motor bucket. I get 15c per lb for them./:>

  24. The Following User Says Thank You to ozzy214 for This Post:


  25. #18
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    I set the tar ones on a slanted computer side piece with a pan at the bottom set a propain torch under it, the tar runs into the pan. when finnished I throw them in a bucket of Gasoline, they come out as bright and shiney transformers @ .30 per lb. or ready for break down.

  26. The Following User Says Thank You to EcoSafe for This Post:


  27. #19
    Scrapette started this thread.
    Scrapette's Avatar
    SMF Badges of Honor

    Member since
    Oct 2011
    Location
    Kentucky USA
    Posts
    942
    Thanks
    2,392
    Thanked 924 Times in 414 Posts
    Quote Originally Posted by olddude View Post
    I set the tar ones on a slanted computer side piece with a pan at the bottom set a propain torch under it, the tar runs into the pan. when finnished I throw them in a bucket of Gasoline, they come out as bright and shiney transformers @ .30 per lb. or ready for break down.
    My thanks button isn't working, so I wanted to thank you, olddude for giving me some ideas.

  28. #20
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    oops forgot make sure they are cool before throwing them in the gasolne.

  29. The Following 2 Users say Thank You for This Post by EcoSafe:



  30. Similar threads on the Scrap Metal Forum

    1. ballast
      By copycat in forum Scrap Metal Questions and Answers
      Replies: 6
      Last Post: 07-03-2012, 10:01 PM
    2. Ballast info?
      By Rio in forum General Electronics Recycling
      Replies: 4
      Last Post: 04-26-2012, 07:21 PM
    3. Electronic Ballast as E-scrap?
      By thxdts in forum General Electronics Recycling
      Replies: 3
      Last Post: 03-06-2012, 05:37 PM
    4. Electronic Ballast as E-scrap?
      By thxdts in forum Scrap Metal Questions and Answers
      Replies: 0
      Last Post: 03-06-2012, 10:10 AM
    5. HPS/MH Ballast
      By Peter_Griffin in forum Scrap Metal Questions and Answers
      Replies: 5
      Last Post: 07-07-2011, 02:50 AM

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook