Results 1 to 16 of 16
  1. #1
    Mick started this thread.
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts

    Is it Stainless Steel, Chrome-plated Brass or Aluminum?

    I had this happen today and figured I can't be the ONLY person in the world to get confused. I'd done a "quick sort" and had a barrel of what I thought to be Stainless Steel turn out to be some brass that was chrome-plated and one piece of aluminum. What confused me was not thinking that faucets are likely brass; not stainless steel (the tub or sinks will perhaps be stainless steel). So, this is the "procedure" I came up with:

    (This applies only to those "shiny" pieces).

    First- Is it magnetic? If it is, It's probably Stainless Steel (or chrome plated steel). If not; it could still be Stainless, but might be Aluminum or Chrome-plated Brass. Second - Test with a grinder - sparks means Stainless Steel. No sparks means Aluminum or Chrome-plated Brass. Third - Use the grinder to grind off a section - if it stays silvery, it's Aluminum. If it's more yellow or gold colored, it's Brass.

    A lot of times, pots and pans will be marked on the underside - "Stainless Steel" or "Aluminum". Another thing is to consider the object's use. If it's used around high heat, it is more likely Aluminum (ie: heat sink, motors). If it's used around water, it's likely copper (as in lines) or brass (as in faucets or valves).



    Stainless Steel is made using Chromium (chrome), so if it's true Stainless, it will have a uniform appearance throughout. Cut or grind through the piece of metal to make sure it's not just chrome-plated steel.

    Check with your yard regarding how to separate various grades of Stainless Steel. My yard has me throw any magnetic stainless steel with #1 iron.

    Please feel free to correct or dispute any of this as it's just what I came up with.
    People may laugh at me, but that's ok. I laugh all the way to the bank.

  2. The Following 11 Users say Thank You for This Post by Mick:



  3. #2
    KzScrapper's Avatar
    SMF Badges of Honor


    Member since
    Apr 2011
    Location
    Denver Metro, CO
    Posts
    4,841
    Thanks
    7,019
    Thanked 5,792 Times in 2,417 Posts
    Glad you posted this Mick...I broke down a bunch of faucets this weekend and the trim plates on a few had me scratching my head because magnet didn't stick, silver color all the way thru but no sparks. It was pretty sunny so maybe I missed them, not sure. I put them with the brass for now and thought I would look at them again before going in.
    Recyclable Material Merchant Wholesaler
    Certified Zip-Tie Mechanic
    "Give them enough so they can do something with it, but not too much that they won't do nothing."

  4. #3
    Scraplogic's Avatar
    SMF Badges of Honor


    Member since
    May 2011
    Location
    Greater Twin Cities Metopolitan Area
    Posts
    61
    Thanks
    42
    Thanked 29 Times in 19 Posts
    Antennas are brass, but they are almost always silver colored. If you're ever rushing and not going to grab whole TVs, boom boxes, etc, at least snap the antenna when you cut cords and run. However, with more time and attention, antennas are simple to unscrew.

    Another brass item used around hot water --- espresso machines. Not the regular coffee makers, but espresso machines often have brass components, and they are rarely yellow. Silver colored and non-magnetic. Brew basket and portafilter are usually brass. Milk steaming pitcher is usually stainless steel. If it's 16oz or bigger it's worth selling instead of scrapping.

    Bent knitting and crochet needles are quite often aluminum. Cut off the little magnetic back end. Light weight, so resell the good ones at the yardsale. They'll go.
    Last edited by Scraplogic; 05-31-2011 at 10:40 PM.

  5. The Following User Says Thank You to Scraplogic for This Post:


  6. #4
    SMF Badges of Honor


    Member since
    Nov 2010
    Posts
    165
    Thanks
    23
    Thanked 69 Times in 36 Posts
    Quote Originally Posted by Mick View Post
    I had this happen today and figured I can't be the ONLY person in the world to get confused. I'd done a "quick sort" and had a barrel of what I thought to be Stainless Steel turn out to be some brass that was chrome-plated and one piece of aluminum. What confused me was not thinking that faucets are likely brass
    When sorting brass items, you need to keep nickel brass (cupronickel, copper-nickel alloy) into consideration as well. It is worth more then regular brass, just as dense, more corrosion resistant, except it is white/silver colored. If cupronickel tarnishes and corrodes, it will have green spots like yellow brass or copper.

    Also, many items that are made of brass, can just as easily be made of zinc. Zinc is just as heavy as brass, except it is dull grey. Zinc is commonly bought by yards separate from aluminum, but the two are commonly confused for one another because of the similar color.

  7. The Following 2 Users say Thank You for This Post by TheMetalizer:


  8. #5
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    dang I just posted asking some of those questions. one faucit I cut through, is white all the way through, but heavy like brass ir is not alu and gives no sparks ?

  9. #6
    Mick started this thread.
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts
    I just answered your other post, but didn't think of nickel. I don't sort zinc (just throw it with aluminum) so never even a consideration.

  10. #7
    SMF Badges of Honor


    Member since
    Jun 2011
    Location
    North Central Washington
    Posts
    58
    Thanks
    7
    Thanked 13 Times in 8 Posts
    Die Cast is also common in Faucets (handles and plates). It looks a lot like aluminum and doesn't spark on grinder but is heavier than aluminum, much like zinc. Some yards keep zinc and die cast separate, and some don't.

  11. #8
    SMF Badges of Honor


    Member since
    May 2011
    Posts
    187
    Thanks
    12
    Thanked 63 Times in 29 Posts
    A nonmagnetic stainless is most likely "303" series. The most common magnetic stainless is "304". I have had alot of yards try to pay straight steel rate on the 304 stainless. 303 usually pays pretty good.

  12. The Following User Says Thank You to fiat128 for This Post:


  13. #9
    SMF Badges of Honor

    Member since
    Apr 2011
    Location
    Dallas, TX
    Posts
    13
    Thanks
    12
    Thanked 2 Times in 1 Post
    I get scrap from a locksmith and much of it at first was hard to sort. For the exact same reasons. A lot of plated brass and die cast zinc ( which pays about half as much as al at my yard). I use pretty much the same process as Mick for this type of scrap as well.

  14. #10
    Jillyenator's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Asheville, NC. Also Arizona.
    Posts
    346
    Thanks
    853
    Thanked 280 Times in 142 Posts
    I need to save this thread and re-read it over and over. There should be a book on how to figure out the different non-ferrous metals.

    And why is some SS magnetic and some not? Do they need to be sorted differently? I will see if there is a thread on this topic.

    So much to learn. I'd buy the book, if there was one.

  15. #11
    Mick started this thread.
    Mick's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Palermo, Me
    Posts
    3,405
    Thanks
    363
    Thanked 3,086 Times in 1,326 Posts

  16. The Following User Says Thank You to Mick for This Post:


  17. #12
    SMF Badges of Honor

    Member since
    Aug 2011
    Posts
    466
    Thanks
    1,612
    Thanked 417 Times in 199 Posts
    I think you ARE reading the book Jillyenator. BTW, thanks for pulling up some old threads. I need to review the book myself.

  18. The Following User Says Thank You to erewen for This Post:


  19. #13
    NHscrapman's Avatar
    SMF Badges of Honor


    Member since
    Jan 2013
    Location
    new hampshire
    Posts
    1,582
    Thanks
    4,076
    Thanked 2,175 Times in 941 Posts
    I have run across The bottom plate of faucets being chrome covered copper as well. It was a designer type faucet not sure if that matters.
    Nothing like grinding expecting silver or yellow and getting orange
    There ain't nothing wrong with an honest days work. Anyone who says otherwise is a fool.- Old Man

  20. The Following User Says Thank You to NHscrapman for This Post:


  21. #14
    Jillyenator's Avatar
    SMF Badges of Honor

    Member since
    Feb 2014
    Location
    Asheville, NC. Also Arizona.
    Posts
    346
    Thanks
    853
    Thanked 280 Times in 142 Posts
    Quote Originally Posted by erewen View Post
    I think you ARE reading the book Jillyenator. BTW, thanks for pulling up some old threads. I need to review the book myself.
    Thanks, Mick. Am reading them now. I thought I'd already read those, but I must've been focusing on the random esoteric threads somehow.

  22. #15
    SMF Badges of Honor

    Member since
    Dec 2013
    Posts
    7
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Getting confused with all that is surely a common thing. Besides that magnet trick you can also judge that by simply hitting on that material with your fingers, as every material vibrates in a different way, but for that you need to have the experience. If you don't have experience then just take a small piece of different materials with you, analyze them one by one and then check that targeted item in order to know about the material.

  23. #16
    cmvegasfan007's Avatar
    SMF Badges of Honor

    Member since
    May 2013
    Location
    kalamazoo MI
    Posts
    6
    Thanks
    0
    Thanked 5 Times in 2 Posts
    Regarding 303 and 304 sst. Magnetic sst isn't 303 or 304. Both are basically and 18-8 sst meaning 18 chrome 8% nickel. Both are nonmagnetic. You I think are talking about 403 sst which is basically a chrome plated steel with VERY little nickle. If your yard is telling you 304 is magnetic you may want to look for another yard because they are 100% incorrect.


  24. Similar threads on the Scrap Metal Forum

    1. Identifying Aluminum & Stainless Steel
      By Meadowview in forum Scrap Metal Identification
      Replies: 14
      Last Post: 08-20-2015, 09:53 PM
    2. Another one :) Brass plated towel bar
      By Gord in forum Scrap Metal Questions and Answers
      Replies: 8
      Last Post: 03-01-2014, 07:46 AM
    3. Is it Stainless Steel or Aluminum?
      By Mick in forum Scrap Metal Questions and Answers
      Replies: 14
      Last Post: 08-16-2012, 08:21 AM
    4. Silver Plated Silverware & Dishes can be Brass or Nickel
      By BiggerHammer in forum Scrap Metal Videos
      Replies: 7
      Last Post: 01-13-2012, 07:34 AM
    5. Tool for identifying stainless steel and aluminum
      By wayne1956 in forum Scrap Metal Identification
      Replies: 9
      Last Post: 07-02-2011, 08:03 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook