Results 1 to 8 of 8

Copper cylinders on refrigerators and A/X units

| Scrap Metal Questions and Answers
  1. #1
    wayne1956 started this thread.
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts

    Copper cylinders on refrigerators and A/X units

    On A/C units there is a sealed copper cylinder that is attached to the compressor, and on the refrigerators it is at the end of some of the tubing with a wire coming out of one end (on the fridge they are about 3/4 inch in diameter and about 4 inches long). They are mostly copper, but do have some steel in them as one end is slightly magnetic. I have kept these separate and was wondering if anyone has any special way they process theirs, and if not what does their yards consider them. I have taken my angle grinder and cut open the larger ones from the A/C units and separated the the steel end off, but the smaller ones from the fridge is a pain but definitely do not want to toss them in the mixed pile.

    Last edited by wayne1956; 07-26-2011 at 10:03 AM. Reason: Meant to say A/C units on thread heading


  2. #2
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    I have several of those set aside I will cut one open today to find out what it is and if it is worth the effort.

    oops looks like you have already done that soooo what was your question ?

  3. #3
    wayne1956 started this thread.
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    I was wondering what the yards consider these cylinders (if they are not broken down)?

  4. #4
    EcoSafe's Avatar
    SMF Badges of Honor



    Member since
    May 2011
    Posts
    3,705
    Thanks
    3,713
    Thanked 6,807 Times in 1,954 Posts
    not sure but probably dirty copper

  5. #5
    wayne1956 started this thread.
    wayne1956's Avatar
    SMF Badges of Honor



    Member since
    Aug 2010
    Location
    Cleburne, TX
    Posts
    705
    Thanks
    195
    Thanked 754 Times in 293 Posts
    That is what I figured myself, just wanted to see if anyone had sold any and what their yards treated it as. I will have to remember to take one with me on my next run and see what the yard says. Might not be a bad thread to start, one where scrap is identified and labeled. Example: Aluminum with steel - dirty aluminum, brass items with steel attached - dirty brass, aluminum running boards from trucks - extruded aluminum, etc.

  6. #6
    SMF Badges of Honor


    Member since
    Nov 2010
    Location
    Boise, ID
    Posts
    2,702
    Thanks
    2,237
    Thanked 2,352 Times in 1,014 Posts
    I cut all of mine open, dump the beads and remove the steel screens. If there is a steel soldered connection, I either heat it up and pull it apart, or cut it off so I have clean copper.

  7. The Following User Says Thank You to IdahoScrapper for This Post:


  8. #7
    Hypoman's Avatar
    SMF Badges of Honor



    Member since
    Dec 2010
    Location
    Indiana
    Posts
    1,268
    Thanks
    2,772
    Thanked 1,331 Times in 512 Posts
    Quote Originally Posted by wayne1956 View Post
    That is what I figured myself, just wanted to see if anyone had sold any and what their yards treated it as. I will have to remember to take one with me on my next run and see what the yard says. Might not be a bad thread to start, one where scrap is identified and labeled. Example: Aluminum with steel - dirty aluminum, brass items with steel attached - dirty brass, aluminum running boards from trucks - extruded aluminum, etc.
    Do It!



  9. #8
    injunjoe's Avatar
    SMF Badges of Honor



    Member since
    Jan 2011
    Location
    Central, FL
    Posts
    1,309
    Thanks
    1,249
    Thanked 1,194 Times in 594 Posts
    Quote Originally Posted by IdahoScrapper View Post
    I cut all of mine open, dump the beads and remove the steel screens. If there is a steel soldered connection, I either heat it up and pull it apart, or cut it off so I have clean copper.
    I see you are talking about the inline dryer, I find most of them are steel with copper fittings on the ends.

    At first I thought Wayne was talking about the reversing valves. These have three copper lines coming in and a solenoid coil on them. These are pretty heavy with just steel pistons in them. The body of this valve is brass and like I say heavy.

    For these I cut in half after smashing the steel bracket that holds the little electric coil on the side. I put in my vise and whack the crap out of it with a beveled hammer, it's held on to the brass like a monkey clinging to a banana! After it is off I cut in half in the middle, then I reach in with needle nose pliers and pull out the pistons from each end. I say "pistons" for lack of a better word. They slide together too and fro, to reverse the freon direction. ( Sorry for the unnecessary information there) .

    The coil that was on there is full of copper, but it is a pain to get out, yes even I hesitate when it comes to cleaning them. I've got a big bucket of just them Should I need money real bad that will be there.
    When the white man discovered this country Indians were running it
    no taxes, no debt, women did all the work.
    White man thought he could improve on a system like this. - Old Cherokee saying

    I did not surrender, they took my horse and made him surrender. - Lone Watie

  10. The Following User Says Thank You to injunjoe for This Post:



  11. Similar threads on the Scrap Metal Forum

    1. Refrigerators and charging to haul them away
      By BurlyGuys in forum A Day in the Life of a Scrapper
      Replies: 8
      Last Post: 09-11-2012, 06:18 PM
    2. question about copper lines in refrigerators
      By redcrossnj in forum Dismantling, Breaking Down & Maximizing Scrap
      Replies: 8
      Last Post: 02-02-2012, 04:03 AM
    3. Medical Oxygen Cylinders
      By rd84 in forum Misc. Metal Recycling
      Replies: 12
      Last Post: 09-22-2011, 06:15 PM
    4. Tanks and cylinders.
      By tinman#30 in forum Scrap Metal Tips and Advice
      Replies: 22
      Last Post: 07-20-2011, 04:50 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

 
Browse the Most Recent Threads
On SMF In THIS CATEGORY.





OR

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

The Scrap Metal Forum

    The Scrap Metal Forum is the #1 scrap metal recycling community in the world. Here we talk about the scrap metal business, making money, where we connect with other scrappers, scrap yards and more.

SMF on Facebook and Twitter

Twitter Facebook